！ Contact our sales office regarding a delivery date or a price since this is a special model. SP158X-002E P.G.Information (Specialized Product) P: TS SMC Corporation Liquid Dispense Pump (Solenoid type) 4-14-1, SOTO-KANDA Contact our sales office regarding a delivery date or a price since this is a special model.
Tighten the joint brackets to a torque of 1.5 to 1.6 Nm. Pin number Signal name BUS IN BUS OUT WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. A unit other than the SI unit has been detected.
Check that the above-mentioned preparation work has been performed correctly, and part A shown in the figure is pushed by hand and makes temporary connection. Part A centre is pushed straight in using a suitable tool, such as pliers. Re-use cannot be performed once it connects the connector for sensor connection completely.
The product is a approved product only if it has a mark on the body. Card URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Rev.A Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2010-2011 SMC Corporation All Rights Reserved
location where it will be used as a support.
INP 1 INP ON 0.50 -35- 6.3 0.1mm [Nm] mm LEF16 M4x0.7 1.5 6 LEF25 M5x0.8 3.0 8 LEF32 M6x1 5.2 9 LEFS40 M8x1.25 12.5 14 A A mm) mm LEF16 M3 3.5 20 LEF25 M4 4.5 24 LEF32 M5 5.5 30 LEFS40 M6 6.6 31 40mm 6.4 6 /1000km /500 -36- 1. 2. 3. 1. 2. a. b. c. d.
Air pressure supplied from A operates on surfaces 1 and 2. (extension) A B Air pressure supplied from B operates on surface 3. (retraction) A B Mounting accuracy improved Positioning holes are provided on the work piece mounting surface for easy alignment. Regulator with check valve is unnecessary A regulator with check valve normally required for a lifting circuit becomes unnecessary.
DC(+) 5 4 3 2 1 A DC(-) A DC(+) OUT1 OUT2 C DC(+) C DC(-) (FUNC) B DC(-) B DC(+) DC(-) NPN PNP -14NO.ZK2-OM00801-B NPN NPN 2 , 26.4 V 80 mA 2 V (NPN ) Assy (ZK2-LWA20-A) PNP PNP 2 , 80 mA2 V (PNP ) Assy (ZK2-LWB20-A) -15NO.ZK2-OM00801-B O O 2 ( :0.080.10 Nm) () -16NO.ZK2-OM00801-B 133 A 1 1 1 1 -17NO.ZK2-OM00801-B OUT1 (P_1)ON (P_1)(H_1)OFF P_1-70.0 kPa H_1:10.0 kPa OUT2
Bracket A (Model: ZS-38-A1) Bracket B (Model: ZS-38-A2) Bracket C (Model: ZS-38-A3) CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
The product is a approved product only if it has a mark on the body.
PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
When a tubing from a company other than SMC is used, ensure that the tubing has an internal diameter and tolerance of 40.3 mm. Lock Sensor CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
as a fulcrum until the manifold is locked.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
as a fulcrum until the manifold is locked.
When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met. This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product or by using a series power supply instead of a switch-mode power supply.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
Upper 3 digits Lower 3 digits Reverse output Warning: + ON Time Part A should then be pressed in using a suitable tool, such as pliers. 2 sec. OFF Initialize mode DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.