When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4.
/2-20 0.88 1.374 0.50 2.06 0.75 0.38 0.56 Note) The clevis pin for NCMC200 is not included.
I COMPACT AND LIGHTWEIGHT 20% Lighter than other types. I EASY TO ATTACH SMALL DIAPHRAGM ACTUATORS The pneumatic and electrical ports are on the side of the body and do not interfere with the feedback lever on the other side. I STABLE OPERATION Control is very stable even on small sized actuators.
When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. OUT2 OUT1 3. When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4.
Linearitv Within t 1% Within t 2% Hvsteresis' Within 1% Repeatabilitv Within 0.5% Within 1% Sensitivitv Within 0.1% Within 0.5% Within 0.2% Within 1% Within 0.2% Within 1% Air Consumption (Max.) less than 0.25 SCFM @ 20 osi 0.7 SCFM @ 70 psi 0.25 SCFM @ 20 psi 0.7 SCFM @ 70 osi 0.25 SCFM @ 20 osi 0.7 SCFM @ 70 psi Supply Pressure Variation Effect (Max.)
Linearitv Within t 1% Within t 2% Hvsteresis' Within 1% Repeatabilitv Within 0.5% Within 1% Sensitivitv Within 0.1% Within 0.5% Within 0.2% Within 1% Within 0.2% Within 1% Air Consumption (Max.) less than 0.25 SCFM @ 20 osi 0.7 SCFM @ 70 psi 0.25 SCFM @ 20 psi 0.7 SCFM @ 70 osi 0.25 SCFM @ 20 osi 0.7 SCFM @ 70 psi Supply Pressure Variation Effect (Max.)
Piping: Common SUP/Common EXH, Stations: 20 Stations, Bracket: Bracket
Cable length (L) [m] A1 1 2 5 6 (17.7) (10.2) (14) (18) 1 3 5 8 A B C 1.5 3 5 8 A6 B1 B3 A1 A3 B6 (13.5) 1 2 (5.7) 15 16 Connector B Connector D (30.7) L (11) (14.7) (10) 8 A B C LE-CP/Cable length: 8 m, 10 m, 15 m, 20 m ( Produced upon receipt of order) 10 15 Actuator side Controller side 20 (5.5) (6.3) (5.7) (14.2) Connector C (Terminal no.)
Do not use tools on the pressure regulator knob as this may cause damage. It must be operated manually. Maintenance Caution Warning 1. Be sure to unlock the knob before adjusting the pressure and lock it after setting the pressure. Failure to follow this procedure can cause damage to the knob and the outlet pressure may fluctuate. Pull the pressure regulator knob to unlock.
Standard Variation Bore Size (mm) Standard Stroke (mm) Page CJ1 Built-in Magnet CJP Standard Style Series CJP Double Acting (Non-lube) 6 5,10,15,20 10,15 5,10,15,20,(25),30 Single Rod 1.2-2 6 CJ2 10 CM2 Single Rod Spring return Single Acting (Non-lube) 15 5/10/15 1.2-8 C85 CG1 How to Order/Double Acting MB C95 CA1 CS1 Standard stroke (mm) Rod end thread With thread Without thread B 5, 10, 15, 20
II Air Cylinder Drive Systems Total Stroke Time and Speed at the End Series SV Series SV1000 Applicable bore size: 20, 25, 32, 40 Applicable related components Total stroke time s Solenoid valve Tubing Speed controller Silencer 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 200 CM2 20 50% 70% 10% 30% 150 Stroke mm AS2201F -01-06 AS2200-01 70% 100 50 10% 30% 50% 0 200 CM2 25 150 Stroke mm AS2201F
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
To install a directional switching valve, do so on the output side of the pressure-reducing valve. 1. If drainage or debris is present in the supply pressure line, the fixed throttle becomes clogged, resulting in a malfunction. Therefore, in addition to the air filter (SMCs AF series), make sure to use a mist separator (SMCs AM, AFM series).
From the above 2. position, turn the adjustment needle 1/4 to 1 turn clockwise. 1 kPa = 7.5 mmHg 1 kPa = 7.5 mmHg 101 101 Supply pressure (kPa) Supply pressure (kPa) Applicable adsorption nozzle range Applicable adsorption nozzle range 50 50 3. 2. 1. 20 20 ZSE ISE Right 0.2 0.3 0.4 0.5 0.6 0.7 0.3 0.5 0.7 0.9 1.1 1/4 to 1 turn Right Left PSE Adsorption nozzle diameter (mm) Adsorption nozzle
Dead volume LVM11: 11 l or less LVM1R, LVM11: 20 l or less The dead volume enclosed by the body and the diaphragm Valve width ( ): 13 mm 2 port 3 port Valve width 9.5 mm (LVM090), 20 mm (LVM200) are also available.
Tube gasket NBR CG1N32-PS Valve seal CG1N40-PS Valve retainer gasket With air cushion CG1A20-PS 20 25 32 40 CG1A20-PS CG1A25-PS CG1A32-PS CG1A40-PS Disassembly/Replacement CG1A25-PS Set of left nos. @2, @3, @4, @5, @6. Caution CG1A32-PS CG1A40-PS 1. Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2.
9 @0 @1 With rubber bumper Rod seal Piston seal CG1WN20-PS 20 25 32 40 CG1WN20-PS CG1WN25-PS CG1WN32-PS CG1WN40-PS CG1WN25-PS Set of left nos. !7, !8, !9. Tube gasket NBR CG1WN32-PS Valve seal CG1WN40-PS Valve retainer gasket With air cushion CG1WA20-PS 20 25 32 40 CG1WA20-PS CG1WA25-PS CG1WA32-PS CG1WA40-PS Disassembly/Replacement CG1WA25-PS Set of left nos. !7, !8, !9, @0, @1.
Additionally, do not put the tube end in the liquid. This may cause the back pressure to be applied, resulting in poor performance. 3.Liquids cannot be collected by the air. 1076 A
High temp. cut off alarm ERR12 Low temp. cut off alarm ERR13 Unused Output failure alarm ERR15 D2 23 22 21 20 Upper temperature limit alarm WRN Lower temperature limit alarm WRN Thermostat alarm ERR14 DC power supply failure alarm ERR11 D3 23 22 21 20 External sensor failure alarm ERR18 Internal sensor failure alarm ERR17 During Auto tuning or auto tuning warning ERR19 Flow switch alarm