OMR0032 Do not use the product in an environment subjected to cyclic temperature changes. It will cause failure of the controller or its peripheral devices. 97 - 6. Do not use in a place where surges are generated.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
Make sure workpieces mounted on the table do not interfere with other workpieces or the facilities around the table.
Do not operate by fixing the table and moving the actuator body. 15. Check the specifications for the minimum speed of each actuator. Failure to do so may result in unexpected malfunctions such as knocking.
Do not disassemble the cables. Use only specified cables. 3. Do not connect or disconnect the wires, cables and connectors when the power is turned on. Caution 1. Wiring securely. Do not apply any voltage to the terminals other than those specified in the Operation Manual. 2. Wire the connector securely. 3. Take appropriate measures against noise.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 5. Do not allow short circuiting of loads.
software version do version and configuration software version not match.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/sXor more for reed switches and 1000m/sXor more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not apply excessive lateral load to the piston rod.
Do not drop or bump. Do not drop, bump or apply excessive impacts (1000m/s or more for solid state switches) while handling. Although the external body of the switch (switch case) may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a rotary actuator by the auto switch lead wires. 5. Do not allow short circuit of loads.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. 5. Do not allow short circuit of loads.
Do not Do not operate the product outside of the specifications. Do not use the product with flammable or harmful fluids. Fire, malfunction, or damage to the product may result. Check the specifications before use. Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a rotary actuator by the auto switch lead wires. Never carry a actuator by its lead wires.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300ms or more for reed switches and 1000ms or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. 6. Avoid incorrect wiring.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300ms or more for reed switches and 1000ms or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. 6. Avoid incorrect wiring.
Do not move the cover upward inadvertently during end plate installation.
Therefore, do not inadvertently move the setting of the guide adjustment unit. 2. Do not perform operation that results in negative pressure inside the cylinder. 2. Do not operate with the cushion needle completely closed.