1 Blow Gun Series VMG K M H D MS Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com T VMG Pressure loss is less than 1%. (nozz K M H Caution D 1. Do not apply the blow gun to flammable, explosive or toxic substances such as gas, fuel gas or refrigerant. Such substances may exude from inside the blow gun.
3.4, 0.2mm'. 3 cores (red. dhile, b a.k). cores (red, back),0 5m oig X .Shock reslslance 1000m/S? l102Gl .lnsulalion resistanceMin. 50O (between lead wi and 6) as memured with a sooVDC meger .
3.4, 0.2mm'. 3 cores (red. dhile, b a.k). cores (red, back),0 5m oig X .Shock reslslance 1000m/S? l102Gl .lnsulalion resistanceMin. 50O (between lead wi and 6) as memured with a sooVDC meger .
*Lead wire length symbols: 20in (0.5 m) . Nil (Example) M9N 118in (3 m) . L M9NL 197in (5 m) .
HANDLE LOCK NUT SETTING SPRING RELIEF VALVE EXH&BLEED PILOT VALVE DIAPHRAGM SUP OUT ELEMENT DRAIN COCK DRAIN SUP 1 Setting Main Composite Displacement Pressure MPa +/-Force Displacement OUT Spring Valve spring m m N/m MPa/m m/N Diaphragm Force N m2 Block Diagram -5- 3.
Phillips screwdriver Tightening torque: 0.6+/-0.05 N m Mounting screws (2 pcs.) Blanking plate O-ring (6) Blanking plate assembly Product 19 - 9. Disassembly Drawing 9-1.
Do not use a cable longer than 30 m. Consult with SMC for the use with a cable longer than 30 m. Connect 0 VDC wire (blue line) directly or as close as possible to 0 VDC terminal of the DC power supply.
Adjust the mounting surface level when using the side support. m m m L L L L Fig. 6 -9- Fig. 7 When using the product that has a stroke that exceeds the stroke fine adjustment range, use an intermediate fixing spacer. Refer to the table below for the stroke fine adjustment range and the stroke adjustment range when using the intermediate fixing spacer.
Equivalent to IP65 Linearity within 1% (full span) Hysteresis 0.5% (full span) Repeatability 0.5% (full span) ITV (Electro-pneumatic regulator) Mist separator (0.01 m or less) (0.3 m or more) High-speed response time 0.1sec (without load) Air filter (5 m or less) IR (Precision regulator) W Features 1 Compact Electro-pneumatic Regulator Series ITV0 How to Order Single unit and single unit
M type connector w/ plug and 300 mm lead wire MO M type connector w/o plug and lead wire MN M type connector w/ plug and pins Air Operated Valve DXT474-A Valve Manifold Assembly DXT475 A * * * * * * 02 * Valve Actuation Type Sup.
C Rubber Bumper M Male Rod CM Rubber Bumper & Male Rod Feed Switch B Basic Model A Threaded Mounting Holes.
E* A73L D-A73L Parls M 3 X 0 . 5 X 3 M 3 X 0 . 5 X 5 M 3 X 0 . 5 X 5 M 3 X 0 . 5 X 5 tvl3x0.5x5 @ Rotary Actuator Series:NCRAl l n ck and pinion rype ||m 30(17Ie) 50121,63(2 %),80(3 %),1 0o{4) Fluid Air Air o o o o 90' 180' 100" 190" Rotatio 1 ) o r)o Basic o o Shaft Singleend Doubleend o o o Body option With ctshion a Wlthalctqruitph -oand to 200. lrom 180" model.
(Type 20 Manifold) SYJ3 2 5 M 1 M3 0 Body ported Base mounted (4 port) 2 SYJ3 3 5 M 0 (Manifold use only) Base mounted (5 port) SYJ3 4 M 2 0 5 4 port Port size Coil specifications Manual override Nil Standard Nil: Non-locking push type Nil: Without sub-plate With power saving circuit T (24, 12 VDC only) Power saving circuit is not available in the case of W type.
(Type 20 manifold) 10 23 5 M 1 M3 SYJ3 Body ported Base mounted (4 port) 2 10 SYJ3 33 5 M (Manifold use only) Base mounted (5 port) SYJ3 43 M 2 5 10 Clean series 4 port Port size Coil specifications Manual override Nil Standard With power saving circuit <24, 12 VDC only> Nil: Non-locking push type Nil: Without sub-plate T Power saving circuit is not available in the case of "W" type.
Locking type manual override While pressing the M/O knob, turn it 90 counter clockwise. When the mark on the cap is aligned with the OFF mark on the M/O knob, the lock will be released (the lock will remain in a released condition). To operate the lock, turn the M/O knob 90 clockwise while pressing it all the way down, and align the cap's mark with the M/O knob's ON mark.
Nil S n M L Auto switch type Bore size Nil Without auto switch (built-in magnet cylinder) 40mm 50mm 63mm 40 50 63 Refer to the table below for auto switch models. Locking direction Cylinder stroke (mm) Refer to the standard stroke table on page 3.
Bearing type M L Slide bearing Ball bushing Applicable auto switches Nil Select auto switch models from the table below. Without auto switch Bore size 32 40 50 63 32mm 40mm 50mm 63mm Lead wire length (m) Auto switch model Electrical entry direction Type 0.5 (Nil) 3 (L) 5 (Z) Perpendicular In-line Z76 P P Cylinder stroke mm Reed switch Z73 Refer to the standard stroke table.
C Rubber Bumper M Male Rod CM Rubber Bumper & Male Rod Feed Switch B Basic Model A Threaded Mounting Holes.
Bore size Stroke range head cap screw for Model Bracket CW CT CL CX CD M CZ R mounting pivot bracket (Accessory) Without auto switch With auto switch 15.5 20 25.5 28 15.5 20 25.5 28 4.5 4.5 6.6 6.6 4.5 4.5 6.6 6.6 M4 x 10 L M4 x 10 L M6 x 12 L M4 x 10 L M4 x 10 L M4 x 10 L M6 x 12 L M 6 x 12 L 5 6.5 8 10 5 6.5 8 10 5 to 30 5 to 30 5 to 50 5 to 50 5 to 30 5 to 30 5 to 50 5 to 50 14 15 18 20
Impact resistance of the product is 150[m/s2]. Vibration resistance is 30[m/s2]. Avoid applying vibration exceeding the allowable value to the product. Mounting Warning 1. Install a stop valve on the supply pressure side of the impact blow valve. This will be an emergency stop in case of leakage or breakage. 2. Refer to How to mount a Nozzle on page 4 for assembling the nozzle. 3.