Title not found

The load should be applied to the piston rod in an axial direction.

Air Cylinder NCJ2 Series Miniature Stainless Steel Body

The load should be applied to the piston rod in an axial direction.

20

Do not use in an atmosphere of corrosive gases, chemicals, sea water, water or water vapor or in an environment where such substances may adhere. 2.Provide shading in an environment where the product is exposed to the sunlight. 3. Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem.

Compact Cylinder with Lock Series CLQ

CNG YA-03 YA-05 YA-08 YA-10 18 6.8 16 6 42 6.5 10 YA 03 20 9 20 8 50 6.5 12 MNB Applicable air cylinder bore 26 11 25 10 62 8.5 16 31 14 30 12 76 10.5 18 CNA 03 05 08 10 32, 40 50, 63 80 100 Bore size (mm) 32, 40 50, 63 80 100 Mounting bracket U V W Mass (g) Part no.

IDX-OM-W034

Specification for Option S 10 1 Safety instructions . 10 1 10 2 Specifications . 10 1 Chapter 11 Specification for Option T 11 1 Safety instructions . 11 -1 11 2 Specifications . 11 -1 11 3 Remote operation . 11 -2 11 4 How to connect the power supply and signal cable . 11 -2 11 5 How to re-start the operation . 11 -3 11 6 Electric wiring diagram . 11 -4 Chapter 12 Specification for Option

3 Position Cylinder Series RZQ

Example) Assume circuit C with an operating pressure of 0.5 MPa, load weight of 10 kg, fluctuation to 20 kg and a cylinder bore of 32 mm.

Direct Operated, 2 Port Solenoid Valve, For Water, Oil, Steam, Air, Series VX

) 0.6 0.7 Critical pressure 0.65 [658] (158) 0.5 0.6 0.55 Sonic [656] (151) 0.5 0.4 0.45 [654] (143) 0.4 0.3 0.35 0.3 [650] (133) 0.2 0.25 0.2 [646] (120) 0.15 0.1 0.1 0.05 2 2 2 2 3 2 3 2 3 2 03 04 VX211 VX22 VX23 VX2 4 VX2 50 VX2 60-02 VX2 602 10 15 5 3 5 10 15 20 25 30 4.5 10 15 20 30 40 50 60 3 2 6 30 60 8 25 35 10 20 40 10 35 Flow rate Q kg/h Figures inside [ ] indicate the saturated

Electrostatic Sensor Monitor

Do not use a cable longer than 10 m. Consult with SMC for the use with a cable longer than 10 m.

Compressed Air Preparation Filter

70 0.01 2 40 6000 100 40 0.1 3 90 1000 20 1 4 10 +3 5 5 10 +7 6 0 < Cp 5 +10 7 5 < Cp 10 Cw 0.5 8 0 < Cw 5 9 5 < Cw 10 x Cp > 10 Cw > 10 > 5 [How to Perform a Test to Check the Performance] ISO 12500, which sets out the test method to be used in order to check the filter performance for each of the three kinds of contaminants, is indicated below.

DOC1018150

with an impact tool. adjustment is made between two graduations (for example, 0 10).

SI unit for CC-Link

An example of when the SI unit station number is set to 01 is shown below.

Plate Cylinder

12 14 DH 11 13 13 17 19 DI 17 22 27 32 38 DJ 7 10 10 14 16 Part no.

IDX-OM-W025

Specification for Option L 10 1 Safety instructions . 10 1 10 2 Specification . 10 1 10 3 Maintenance . 10 2 Chapter 11 Specification for Option M 11 1 Safety instructions . 11 1 11 2 Specifications . 11 2 11 3 Cautions for handling the motor type auto drain . 11 2 11 4 Electric circuit . 11 2 Chapter 12 Specification for Option R 12 1 Safety instructions . 12 1 12 2 Specifications . 12

S070

S070 Timer circuit ZNR Light VQ i1: Inrush current i2: Holding current 2) Electrical circuit (1) Adopt an electrical circuit with no chattering generated at the contact. (2) Keep the voltage within the 10% range of the rated voltage.

RSH

Note 3) The figure shows an extended piston rod.

Clean Air Module

The switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 2. Mount switches in locations where there is no vibration greater than 98 m/s2, or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.

Stopper Cylinder

10 10 5 4 3 4 5 3 4 5 3 2 2 2 1 1 1 1 5 10 20 10 5 1 20 30 10 5 1 20 30 Transfer speed (m/min) Transfer speed (m/min) Transfer speed (m/min) Lever-type weight of transferred object and transfer speed graphs (graphs (2) and (3)) show the values at room temperature (20 to 25C).

Intrinsically Safe Valve

Do not install in Zone 0 (as defined in IEC 60079-101:2008) or Zone 20 (as defined in IEC 60079-10-2:2009) Zone 0 area classification: An area in which an explosive gas atmosphere is present continuously or for long periods or frequently.

XM, XY

-10 (FKM) 1.3 x 10-8 External 1.3 x 10-11 (FKM) 1.3 x 10-9 w, e w e Nil A B C P1 70W 1.3 x 10-8 1.3 x 10-11 (FKM) 1.3 x 10-9 Kalrez 1.3 x 10-10 (FKM) Q1 R1 R2 R3 S1 T1 4079 SS592 SS630 SSE38 1232-70 3310-75 Note 1) Values at ambient temperatures, excluding gas permeation.

E-P HYREG ® Series VY1 1

Common external pilotP1 has an M5 screw. Stations Dimension 2 3 4 5 6 123 169 215 261 307 107 153 199 245 291 L1 L2 14-10-17