Pressure Sensor (Example: If the Pressure switch with output impedance of 1k is connected to the A/D converter to detect the analogue output of 5 V, the detected voltage by the A/D converter becomes 5(V) 1(M)/(1(k) + 1(M)) 4.995(V), and there is an error of approximate 0.005 V.) Output impedance R The pressure range in which the Pressure switch satisfies the specifications.
Designation Description 3 Setting the Number of occupied stations Power supply connector Power supply with load voltage for valves and operating voltage for SI unit (M12 5-pin plug, B-coded) 3 1 SV24 V +24 V for solenoid valve Setting Station No. 4 5 2 2 SV0 V 0 V for solenoid valve x10 x1 4 Ground terminal Functional earth (M3 screw) 3 SI24 V +24 V for SI unit operation 0 0 Error (Default
Nil Analog 1 to 5 V Analog 1 to 5 V Analog 4 to 20 mA Analog 1 to 5 V G oC/oF None Under the New Measurement Law, units other than SI (symbol Nil) cannot be used in Japan.
V Yes Grommet 3-wire (NPN) IC circuit 5 V, 12 V Diagnostic indication (2-color display) 3-wire (PNP) 2-wire 12 V 3-wire (NPN) IC circuit 5 V, 12 V Water resistant (2-color indication) M9PA M9PAV 3-wire (PNP) M9BA M9BAV 2-wire 12 V Although it is possible to mount water resistant type auto switches, note that the rotary actuator itself is not of water resistant construction.
2-wire 3-wire(NPN) IC circuit Diagnosis (2-color indicator) MHW MHW 5 V, 12 V Relay, PLC Grommet Yes 24 V 3-wire(PNP) 12 V 2-wire -X M9NAV 3-wire(NPN) Water resistant (2-color indicator) IC circuit 5 V, 12 V M9PAV M9PA 3-wire(PNP) MRHQ M9BAV M9BA 12 V 2-wire Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.
-wire(NPN) IC circuit Diagnosis (2-color indicator) 5 V, 12 V Relay, PLC Grommet Yes 24 V 3-wire(PNP) 12 V 2-wire M9NAV 3-wire(NPN) Water resistant (2-color indicator) IC circuit 5 V, 12 V M9PAV M9PA 3-wire(PNP) M9BAV M9BA 12 V 2-wire Auto switches marked with a symbol are produced upon receipt of order.
200 V 24 V C73 C73C H7A1 H7A2 H7B H7C H7NW H7PW H7BW H7BA H7NF Yes Replay PLC 12V 2 wire Connector Grommet Diagnostic indication (2-color) 3 wire (NPN) 5 V, 12 V IC 3 wire (PNP) Grommet 2 wire 12 V Connector 3 wire (NPN) 5 V, 12 V Diagnostic indication (2-color) IC Replay PLC 3 wire (PNP) Yes 24V 12 V 2 wire Water resistant (2-color) Grommet IC Diagnostic output (2-color) Latch type
[Driving to the intermediate position] 24 V 0 V Power supply (5) Alarm Reset ON OFF Alarm reset IN0-3 Input ON OFF Input RESET ON OFF OUT0-3 ON OFF ALARM Output Output BUSY Alarm out Release Hold ALARM is expressed as negative-logic circuit.
Evaporation thermometer V Dustproof filter provided as a standard accessory V All electrical components are located in the front of the product.
Series 10-VQD1000 [Option] 4 Port Direct Operated Poppet Solenoid Valve How to Order Valve Clean series Valve option Nil Standard (2 W) V Vacuum (2 W) U For large flow (3.2 W) W For large flow, Vacuum (3.2 W) Energy saving type Rated voltage 5 24 VDC 6 12 VDC Body type 2 Body ported (Single unit) 3 Body ported (Manifold) 5 Base mounted 10 V Q D 1 1 5 1 U 5 L M5 Electrical entry
The power supply for the unit should be 0 V as the standard for both power supply for output as well as power supply for control/input. VQZ SQ VFS +24 V +24 V Power supply for output Power supply for output VFR 0 V 0 V Power supply for control/input +24 V Power supply for control/input 24 V VQ7 4. Do not install a unit in a place where it can be used as a foothold.
12 V Solid state switch Relay, PLC 24 V Grommet Yes 12 V 5 V, 12 V 12 V 100 V or less 100 V IC circuit no Yes Relay, PLC 24 V 2-wire Reed switch Grommet 161
Bore Size: 10mm, Port Thread: M Thread: 6 to 15 Bore; Rc: 20 to 63 Bore, Stroke: 250mm
Magnet: None, Series: A2 (Standard), Mounting: B (Basic), Tube Material: F (Steel Tube), Bore Size: 80mm, Port Thread: Rc, Stroke: 250mm, Rod Boot: None, Cushion: Air Cushion
Magnet: None, Series: A2 (Standard), Mounting: D (Double Clevis), Tube Material: F (Steel Tube), Bore Size: 80mm, Port Thread: Rc, Stroke: 250mm, Rod Boot: None, Cushion: Air Cushion
Magnet: None, Mounting: C (Single Clevis), Bore: 20mm, Stroke: 250mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap
The MB series medium duty tie rod cylinder offers an improved design that enhances cylinder operation and ease of use. The standard air cushion utilizes a floating cushion seal to eliminate piston rod bouncing. The cushion volume has been elevated permitting about 30% more allowable kinetic energy absorption. The port and captive cushion adjustment valve are located on the same side of cap