Ｖ cylinder Tightening torque Bore size Socket Tightening torque[Nm] 40,50 13 (M8) 7.4 63 17 (M10) 20 80,100 19 (M12) 29 2 4 Tie rod tightening order. 14 3-2-2. Removal of seals 1) Rod seal Insert a precision screwdriver from the front of the cover to pull out the seal as shown in Fig. 4.
Isolate the valve and re-tighten the bolts. (13) (14) Lessen the oil supply amount to the degree that oill does not spout out of the exhaust port [3(EB), 5(EA), PE port]. *In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port.
Same as Investigation method. 69 No.EX-OMS0014-A Fault No. 13 Fault Possible cause Investigation method Countermeasures Solenoid valves not operating correctly. Solenoid valve LED is ON. Solenoid valve failure Refer to the troubleshooting of the solenoid valve. Same as Investigation method.
Do not remove the name plate. 13. Perform periodic inspections and confirm normal 1. These products are intended for use in general factory EX500/EX250/EX126 Precautions automation equipment.
No.EX-OMM0008-D PRODUCT NAME Fieldbus system (SI unit compatible CompoNetTM) MODEL / Series / Product Number EX12#-SCM# Table of Contents Safety Instructions 2 Product Summary 7 Model Identification and How to Order 7 Summary of Product parts 8 Mounting and Installation 13 Wiring 13 Setting 18 Mounting of Objects 20 Maintenance 27 Troubleshooting 28 Specifications 31 Specifications 31 Dimensions
Isolate the valve and re-tighten the bolts. (13) (14) Lessen the oil supply amount to the degree that oill does not spout out of the exhaust port [3(EB), 5(EA), PE port]. *In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port.
(Figure-13) Pick and pull. Figure-13 2) Tube gasket Pry it out with a precision screwdriver. 15 - 6-3-3. Grease application Caution Use SMC standard grease.
Wiring of the power supply cable . 13 3-2-3. Wiring of the AC adapter . 13 3-3. Timing chart . 14 4. Function . 14 4-1. Name of Parts . 14 4-2. Adjustment of offset voltage (ion balance) . 15 4-3. Adjustment of air flow . 15 4-4. Maintenance Warning Function and Cleaning . 15 4-5. Replacement of Cartridge Case . 17 4-6. Alarm function . 17 5. Performance . 18 6. Dimensions . 19 7.
(Refer to Page 13 to 14) 22 - Change to recommended balanced circuit. (Refer to Page 13 to 14) b. Adjust the regulator valve. Check if the locked status is balanced. c. Install an air tank so that pressure fluctuation does not occur when supplying air to the lock unit and cylinder. d. After stopping by locking, release the lock after waiting for 0.5sec or longer. a.
For type W, DC voltage For connector cable of M8 connector, is only available. refer to page 13 and 14. Note 1) Enter the cable length symbols in CE-compliant: For DC only.
No.PS-OMM0007-I PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE40A(F) ISE40A Table of Contents Safety Instructions 2 Model Indication and How to Order 9 Summary of Product parts 12 Definition and terminology 13 Mounting and Installation 16 Installation 16 Piping 18 Wiring 20 Pressure Setting 23 Measurement mode 23 Function Setting 25 Function selection mode 25 Default
Decline in the power supply voltage (13) (7) AC voltage was applied to a DC pilot valve. 13 VEX-OMT0003 Countermeasures No. Countermeasures (1) Connect wires correctly. (2) Replace the parts. (3) Replace the parts or connect wires correctly. (4) Replace the valve. (5) Adjust the pressure so that pilot pressure is within the specified range during operation.
Guaranteed term and guaranteed range 13 8. Parts replacement procedure 14 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Then reapply the power supply and push MIDDLE button. 3 positions : See the circuit on page 13. 5 positions : See the circuit on page 25. ( ) Check the voltage and adjust it if necessary and then perform alarm reset. Power supply voltage is excessive or lower than limit for operation.
53 2.3 30 AL40-A 50 52 26 8.5 12.5 70 2.3 35 AL40-06-A 50 52 25 8.5 12.5 70 2.3 34 AL50-A 70 66 35 11 13 90 3.2 47 AL60-A 70 66 35 11 13 90 3.2 47 Semi-standard specifications Drain cock with barb fitting Metal bowl Metal bowl with sight glass Metal bowl with sight glass and drain cock With drain cock Metal bowl, drain cock Model 59.9 56.3 59.3 87.7 84.5 87.5 115.1 123.6 104.1 117.6
Wiring . 13 3-2-1. Connection Circuit . 13 3-2-2. Wiring of the Power Supply Cable . 15 3-2-3. Wiring of the AC Adapter . 15 3-3. Timingchart . 16 4. Function . 17 4-1. Name of Parts. 17 4-2. Adjustment of Offset Voltage . 17 4-3. Adjustment of Air Flow . 18 4-4. Emitter Dirt Detection and Cleaning. 19 4-4-1. Manual Cleaning . 19 4-4-2.
Apply grease all over the seal and inner surface of the bushing as shown in Fig. 13. If it is difficult to apply grease, for example to a small bore diameter, use a precision screwdriver. Do not scratch any surface with the screwdriver. 2) Piston seal (Fig. 12, ) Mount with care not to twist the piston seal.
This matches the controller. (2) Check Parallel I/O configuration matches (NPN or PNP). (1) LEMB25T-300 NPN (2) -13- 2.3 Construction (1) LEMB Motor option With lock Option: Stroke adjuster No. Description Material Note No.
50.5 53.5 37.5 40.5 10 14 0 26.5 23.5 10 3 Bore size [mm] G GA GB GC H HA J K L MM ML NN OA OB OL P PA PB PW Q 100 st or less Over 100 st Nil TN TF 12 25 10 6 7 10 54 M5 12.5 12.5 17 M4 x 0.7 10 M4 x 0.7 4.3 8 4.5 M5 x 0.8 11.5 8 16 14 16 29 12.5 5.5 7.5 11.5 59 M3.5 14.5 14.5 20 M5 x 0.8 11 M5 x 0.8 4.3 8 4.5 M5 x 0.8 11.5 9.5 16.5 15 20 33 12.5 9.5 9.5 12.5 78 M5 16.5 16.5 23 M5 x 0.8 13
13 Rc 1/4 (G1/4, NPT1/4) (Finger opening port) 16 22 5 6.45 MHW2-50D1 6 Right angle finger type 78 37 24 30 39 12 58 85 52 4 x M10 x 1.5 through (Thread for mounting attachment) 718 MHY2/MHW2 Series Auto Switch Installation Examples and Mounting Positions Various auto switch applications are possible through different combinations of auto switch quantities and detecting positions.