Clean Air Filter Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
Normally this relationship is expressed in ejector standard use. In graph, Pmax is max. vacuum pressure and Qmax is max. suction flow. The valves are specified according to catalog use. Changes in vacuum pressure are expressed in the order below. 1. When ejector suction port is covered and made airtight, suction flow becomes 0 and vacuum pressure is at maximum value (Pmax). 2.
This may cause damage. 9. If product is to be used in a public place, ensure product is not directed at people or used in a manner that could adversely affect the environment. 10.For other cautions, refer to the 2 Port Solenoid Valves for Fluid Control Precautions. 11.
Note 1) This displacement is measured when a 15 mm aluminum plate is mounted and fixed on the table. Note 2) Check the clearance and play of the guide separately.
Red ON Pin number Signal name BUS IN BUS OUT 1 2 1 2 The power supply voltage for output is OFF or out of range. (When diagnostic parameter is disabled) 1 TX+ OFF WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. 2 RX+ Warning: PWR(V) The power supply for output is properly.
U + . 1 1 + . 2 4 = | . t g 0 2 Port location on head cover Perpendiculat to the cylinder axis or in-line with the cylinder axis locations are available for basic type. (06 is not avaihble in perpendicular type.)
PLC PLC Redundancy manager Redundancy manager Client Client Client Client Client Client Client Client 1 2 3 4 1 2 3 4 Disconnected location Normal flow of data Data flow when the communication cable is disconnected Fast Start Up function Approx. 0.5 sec. Approx. 10 sec.
U + . 1 1 + . 2 4 = | . t g 0 2 Port location on head cover Perpendiculat to the cylinder axis or in-line with the cylinder axis locations are available for basic type. (06 is not avaihble in perpendicular type.)
Push Button/VM1000-4N-32, VM1000-4NU-32 VM1100-4N-32, VM1100-4NU-32 JIS Symbol/2 port 3 port Panel mounted hole Applicable tube 0.5MPa supply T0425 TU0425, T0403, TS0425 Side piping 3 ports 2 ports VM1100-4NU-32 VM1000-4NU-32 VM1100-4N-32 VM1000-4N-32 6N F.O.F. 2.5mm P.T. 2mm O.T. 4.5mm T.T. 3.5-9 VM1000 Series VM1000/Bottom Piping JIS Symbol/2 port 3 port Basic/VM1010-4N-00, VM1010-4NU-
5 1 l 3 = % =V2 0 1 0 3 NVEP 31 4 Size I Pressure Size Code PSIG (Kg7cm2) NPTF (Base mount type) 2 1 7-90 (0.s-5.5)O2=t/c 03=% 2 15-135 (1-9) 4 1 o.7 -22.5 (0.051.s) 03=% O4=th 06 =Vr Subplates (NVEF2120; NVEFII20; NVERI I20) Part No.
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.) Note 6) The display unit is conformed to CE mark.
Green ON 3 4 3 4 2 Display cover Open at the switch configuration. Diagnostic error of I/O unit is detected. Green flashing RX4 Any of the following diagnostic error is detected. (When diagnostic parameter is enabled) Valve ON/OFF counter has exceeded the set value. Valve is short circuited or disconnected.
Warning: 1 2 1 2 Green ST(M) LED is flashing. 1 TD+ Either of the following conditions: The valve ON/OFF counter has exceeded the set value. The valve is short circuited or disconnected. Red ST(M) LED is flashing. 2 RD+ TD3 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. (2)Add more I/O units.
When conformity to UL is necessary the SI unit must be used with a UL1310 Class 2 power supply. The product is a UL approved product only if it has a mark on the body. Outline Dimensions 0 2 4 6 0 0 4 6 Bit No.
PS Without PSE56 0 01 Z I SE1 2 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP Note 1) Current output type cannot be connected to PSE20 and PSE30. Note 2) The connector is not connected to the cable and is supplied loose at the time of shipment.
Selection of air quality by purpose For these cases, degree of quality is 15 4 +3 5 specified as 1, 4, and 2 respectively. 40 5 +7 25 Refer to Guide (1). Refer to Guide (2). Refer to Guide (3). Refer to below piping system chart. Refer to Guide (4) page 14-14-4.
The power supply voltage for outputs is abnormal. Warning: 1 2 1 2 1 TD+ Red PWR(V) LED is ON. 2 RD+ TD3 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. A unit other than the SI unit has been detected. (2)Add more I/O units.
This product is not designed to be explosion proof. Caution for maintenance (1) Be sure to turn-off all power supplies. (2) Be sure that there is no foreign object in any of units. (3) Be sure that gasket is lined properly. (4) Be sure that tightening torque is according to specification. Set SW7 to 0. (SW7 is not used.) Set SW8 to 1.
Red ON SF The direct current power supply to combine should be UL1310 Class 2 power supply when conformity to UL is necessary. The output rating is tested as a DC output for General use. 1 Node flashing test. Green flashing PROFINET communication is established. OFF (2)Mount the end plate bracket (EX600-ZMA2) to the end plate at the opposite end to the valves, using 2-M4 x 14 screws.
If the drainage is not discharged properly, it will flow over to the outlet side. Air Supply Caution 1. The mist separator is not applicable to gases other than compressed air. The mist separator is not applicable to gases other than compressed air (example: oxygen, hydrogen, flammable gas, mixed gas). Sight glass 2.