Direct Solenoid Mo(rntlng Bas MT33&rl 16. 2 Mounlhg 8a Sclws M5x10 DIRECTIOIIAL AIR VALVES DIMENSIONS/PARTS LIST 3125 3145 NVS 31 SEFIES NVS 3115, NVS 3125 FOOT rOUa{T[{c Prlmary mountlng mlhod ls fool mountlng on the nd of th6 body.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling except for priming the pump. 5 11.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
If you do not agree to the following disclaimer, you may not use or copy this software. "Disclaimer" 1.
CAUTION Do not allow air flow that exceeds the rated flow. If the air flow is allowed outlet side the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. Do not use in a low pressure application (such as a blower).
Do not use the product where these are present.
Do not use the product where these are present.
Do not use the product where these are present.
CAUTION Do not allow air flow that exceeds the rated flow. If the air flow is allowed outlet side the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. Do not use in a low pressure application (such as a blower).
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the handle assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the handle assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Pressure Setting Wiring Warning Warning 1. Setting of vacuum pressure 1. Do not apply excessive pulling force on the lead wire. It may cause a malfunction or damage. 2.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling except for priming the pump. 5 11.
Note2) Do not move the clamp side switch. Clamp side switch Unclamp side switch Unclamp angle display 16 - Fix the lead wire of the unclamp side switch with the lead wire retainer. Note3) Fix the lead wire without slack to prevent interference with the internal parts of the cylinder. Note4) Use the lead wire retainers provided below the bottom of the switch.
Do not remove it and attention should be taken not to deform nor gouge. 14 Other Cautions for Operation 7-1) Environment The piston slider has iron part inside. Keep the cylinder tube away from the water. Do not use in atmosphere or place where might corrode the cylinder. Protect the cylinder with cover where it is exposed to dust and particle, drop of water/oil.
Do not use the product where these are present.
Body Caution M5 hexagon socket head cap screw q M6 special screw (Do not disassemble.) Caution M6 special screw (Do not disassemble.) M5 hexagon socket head cap screw w Fig.1 Caution 1. Before disassembling, be sure to shut off the pressure supply, and then release the residual pressure. 2. After assembly, confirm that there is no fluid leakage.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.