NVEPA|VEFseies 5 1 l 3 = % =V2 0 1 0 3 NVEP 31 4 Size I Pressure Size Code PSIG (Kg7cm2) NPTF (Base mount type) 2 1 7-90 (0.s-5.5)O2=t/c 03=% 2 15-135 (1-9) 4 1 o.7 -22.5 (0.051.s) 03=% O4=th 06 =Vr Subplates (NVEF2120; NVEFII20; NVERI I20) Part No.
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.) Note 6) The display unit is conformed to CE mark.
Green ON 3 4 3 4 2 Display cover Open at the switch configuration. Diagnostic error of I/O unit is detected. Green flashing RX4 Any of the following diagnostic error is detected. (When diagnostic parameter is enabled) Valve ON/OFF counter has exceeded the set value. Valve is short circuited or disconnected.
Warning: 1 2 1 2 Green ST(M) LED is flashing. 1 TD+ Either of the following conditions: The valve ON/OFF counter has exceeded the set value. The valve is short circuited or disconnected. Red ST(M) LED is flashing. 2 RD+ TD3 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. (2)Add more I/O units.
When conformity to UL is necessary the SI unit must be used with a UL1310 Class 2 power supply. The product is a UL approved product only if it has a mark on the body. Outline Dimensions 0 2 4 6 0 0 4 6 Bit No.
PS Without PSE56 0 01 Z I SE1 2 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP Note 1) Current output type cannot be connected to PSE20 and PSE30. Note 2) The connector is not connected to the cable and is supplied loose at the time of shipment.
Selection of air quality by purpose For these cases, degree of quality is 15 4 +3 5 specified as 1, 4, and 2 respectively. 40 5 +7 25 Refer to Guide (1). Refer to Guide (2). Refer to Guide (3). Refer to below piping system chart. Refer to Guide (4) page 14-14-4.
The power supply voltage for outputs is abnormal. Warning: 1 2 1 2 1 TD+ Red PWR(V) LED is ON. 2 RD+ TD3 DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. A unit other than the SI unit has been detected. (2)Add more I/O units.
This product is not designed to be explosion proof. Caution for maintenance (1) Be sure to turn-off all power supplies. (2) Be sure that there is no foreign object in any of units. (3) Be sure that gasket is lined properly. (4) Be sure that tightening torque is according to specification. Set SW7 to 0. (SW7 is not used.) Set SW8 to 1.
Red ON SF The direct current power supply to combine should be UL1310 Class 2 power supply when conformity to UL is necessary. The output rating is tested as a DC output for General use. 1 Node flashing test. Green flashing PROFINET communication is established. OFF (2)Mount the end plate bracket (EX600-ZMA2) to the end plate at the opposite end to the valves, using 2-M4 x 14 screws.
If the drainage is not discharged properly, it will flow over to the outlet side. Air Supply Caution 1. The mist separator is not applicable to gases other than compressed air. The mist separator is not applicable to gases other than compressed air (example: oxygen, hydrogen, flammable gas, mixed gas). Sight glass 2.
9 @0 @1 @2 23 Seal kit consists of items !7 through @2 and can be ordered using the seal kit number for each bore size. Cushion seal CHA50-PS Wiper ring NBR CHA63-PS Set of left nos. !7, !8, !9, @0, @1, @2 Rod seal NBR 23 is a non-replaceable part, so it is not included in the seal kit.
9 @0 @1 22 @3 Cylinder tube gasket NBR 2 Set of left nos. !5, !7, !9, @0, @1, @3 Hexagon socket head set screw Carbon steel 1 Nickel plated Rod seal A NBR 1 Rod seal B NBR 1 Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
1 1 1 1 1 2 2 2 1 Relay valve Pressure gauge Diaphragm assembly Valve assembly NLP seal PNY seal Wear ring O-ring NBR NBR Cloth-inserted phenol aldehyde resin NBR Glass fiber-inserted epoxy resin !2 1 Bowl assembly 126059-4A 126060 NBR !3 2 Seal Zinc die-casted !4 Lubrication plug assembly 1 126115AP NBR AF11-2 11307 !5 !
D 3 D C C 2 2 A A B B Dimensions Dimensions (mm) (mm) N: 1/8 (Rc, NPT, NPTF) A B C D F Y N: M5 x 0.8 N: M8 x 1.25 Model A B C D Model ZPT10F-B5 F NL P F NL P F P 10 12 10 12.5 27 1.5 ZPT13F-B5 ZPT20F20 22 13 15 32 36 36 12.5 15.5 10.5 13 27.5 ZPT16F-B5 ZPT25F5 9 8 12 14 2 25 28 16 18 ZPT32F32 36.5 36.5 13 16 32 35 40 50 B8 01 ZPT F(Without buffer/Female thread) Hexagon width across flats
Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. 2) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Plus the built-in programmable display allows you to check the status of your system anytime. 1 PneuAlpha Introduction 1 2 2.
When a special intermediate stroke body is needed, contact SMC.
Description Model ALDU900 ALD900 ALDU600 ALD600 G 126044P 113449(1) 113543(2) 126130P 126044P 126130P Bracket PPA 12661P 12651-1P Panel AL IS430-1 IS430-2 IS420-1 IS420-2 IS430-1 IS430-2 IS420-1 IS420-2 Float switch S1 ALD600 S2 } 1 4 1 2 Note1) Bracket for filter mounting: For Rc 1 ,1 Note2) Bracket for filter mounting: For Rc 2 Thread machining on filter body is needed.