IDX-OM-P026E if an operator does not follow the specified procedures during the operation or maintenance of the product or does not follow the instructions necessary to avoid it.
Please note that the preset input type is not equipped with an output signal function.
RoHS Ionizer IZS40/41/42 Series How to Order Type 40 Standard type IZS 40 IZS 42 1600 1600 10 10 B B Type 40 Type 41/42 Made to Order Bar type Type 41 42 Feedback sensor type Dual AC type IZS41 IZS42 Sensor Symbol Sensor Built-in sensor Feedback sensor Auto balance sensor [High accuracy type] Nil F G Emitter cartridge type/Emitter material Symbol Nil C J K Feedback sensor cannot be used
Please note that the preset input type is not equipped with an output signal function.
Low temperature operation 1) The valve can be used in an ambient temperature of not less than 5C.
. lill| / l(01$enies [0I/$AIllr fiilinm Male Connector: KVH 7 t 6 8 9 1 4 I 1 0 1 3 1 4 24 E ; 40 Consult factorv for irformation " Not available at time ot catalog printing.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.
Therefore, use the dryer in an area where the discharge will not be a problem. AT IDF IDU IDF FS Operation Caution IDFA Turn ON the power after the air dryer has been pressurized. If the power is turned ON before it is pressurized (particularly when the pressure is low), the check valve will not operate properly, possibly creating an abnormally large reactivated air flow rate.
It is recommended to use an automatic drain system for savings in labor. When using an SMC automatic drain system, Model AD402-03D-6-A (Model AD402-04D-6-A for the Model HAA37 units), a base as shown in the following sketch, is required.
Install an air drier or aftercooler before the regulator. Caution 1. Install an air filter at the upstream side of this product. Select an air filter with a filtration degree of 5m or finer. 2. If an excessive amount of carbon powder is present, install a mist separator on the upstream side.
Reduced the attenuation of the ion by an air blow. Equipped with an additional air blow nozzle only for dust removal. Besides the ionized air, the angle and flow rate of the air blow can be adjusted (Optional).
0 0.043 43 8 50 16 40 13 22 5 2 8 12 1.0 M5 1.1-10
Insert an inner sleeve into soft polyurethane tubing when used with a One-touch fitting. Yellow (Y) Green (G) Translucent (N) (1) Yellow brown (YB) Soft polyurethane tubing Fluid Air Iner sleeve 0.6 MPa Refer to the burst pressure characteristics curve.
How to Order 11 LEFS 100 B 1 1 S K 6N 16 w e r t u y o i !0 !1 !2 !
(Note) The wire colour is shown for when an alternative cable is used.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Supply pressure will pass through the main valve resulting in an electrical signal by the pressure sensor @ which provides feedback to the controller O.
Supply pressure will pass through the main valve resulting in an electrical signal by the pressure sensor @ which provides feedback to the controller O.
Cooling Method: A (Air-cooled Refrigeration), Pipe Thread: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 40 [3-phase 380 to 415 VAC (50/60 Hz)]
Cooling Capacity: 300 (CH1: 26 kW; CH2: 1 kW), Pipe Thread: N [NPT (Rc-NPT Thread Adapter Set is Included)], Power Supply: 40 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)]