Maximum operating pressure 1MPa; Meter in or meter out control ; Port sizes: M3, M5, U10/32, 01, 02, 03, 04 ; Various tube O.D. in both metric and inch
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT) Speed controller standard in-line style; Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2; Port sizes: M3, M5, 01, 02, 03, 04
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT) Metal body elbow style; Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2; Meter in or meter out; Port sizes: M3, M5, 10-32UNF, 1/8, 1/4, 3/8, 1/2
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT) Speed controller standard in-line style; Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2; Port sizes: M3, M5, 01, 02, 03, 04
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT) Metal body elbow style; Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2; Meter in or meter out; Port sizes: M3, M5, 10-32UNF, 1/8, 1/4, 3/8, 1/2
m3/sN02NPT1/4118 g90 gC01Rc1/8114 g86 g1 x 10?5 Pa?m3/s
m3/sN02NPT1/4118 g90 gC01Rc1/8114 g86 g1 x 10?5 Pa?m3/s
SI unit for EtherNet/IP TM Match polarity between solenoid valve and SI unit output. -41No.EX-OMX1001 Maintenance Replacement of the SI unit Remove the M3 hexagon screws from the SI unit and release the SI unit from the valve manifold. Replace the SI unit.
Measurement mode Power is supplied Installation Press the SET button between 3 and 5 seconds Mounting by panel mount adapter Fix the panel mount adapter to the Controller with the set screws M3 x 8L (2 pcs.) as attached.
Maintenance Bracket mounting Mount the bracket using the mounting screws (M3 x 5 L) supplied. The required tightening torque is 0.5 to 0.7 Nm. Install the product (with bracket) using the M4 screws (2 pcs.). Bracket thickness is approximately 1.6 mm.
Without flow adjustment valve (using ZS-33-M) With flow adjustment valve (using ZS-33-MS) Mount the product with bracket using M3 screws (4 pcs) or equivalent. Screws are prepared by customer. Refer to the dimension drawing (page 84) for the bracket thickness and mounting hole dimensions.
Mounting bracket Mounting to equipment Item PFMB7201 PFMB7501 PFMB7102 PFMB7202 Model Mounting screws Tightening torque Screw [P_1] Set value of OUT1 100 250 500 1000 URL http://www.smcworld.com PFMB7201 0.45 to 0.55 Nm M3 screws (4 pcs.)
(2 ) (71 ) 0.50.7 Nm M3 -16No.PF-OMS0001CN-A IN8cm 2F.S.
Before Use Digital Flow Switch PFMC7501/7102/7202 Connector pin numbers (on the product)
Mounting screw (M3 x 5 L) Function selection mode Panel mount adapter (can be rotated 90 degrees for mounting). Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Troubleshooting Wiring Wiring of connector Connections should only be made with the power supply turned off.
Mounting by panel mount adapter Fix the panel mount adapter to the controller by the mounting screws M3 x 8 L (2 pcs.).
2 VN*-OMJ0001-B / / / / 1 1 1 1 1 1 1 1.5 .5 .5 .5 *3) *3) *3) *3) 1 1 1 1 1 1 1 1 () 3 VN*-OMJ0001-B 1)-5 2) ( ( ( ( ) ) ) ) () IP IP IP IP65 65 65 65 1) 50mm 2/s 2) 3) 1) 2) 5m 3) 4) 1.5~2 2 4 VN*-OMJ0001-B 3)0.1MPa Nm Rc1/8 79 Rc1/4 1214 Rc3/8 2224 Rc1/2 2830 Rc3/4 2830 Rc1 3638 Rc1 1/4 4042 Rc1 1/2 4850 Rc2 4850 ( ( ( ( 5, 6, 7 5, 6, 7 5, 6, 7 5, 6, 7 ) ) ) ) G1/2 M3
Table 3-5 Signal cable Terminal specification Cable specification Terminal block Recommended screw diameter crimp terminal M3 1.25Y3 0.75 mm2 (AWG18) Shielded cable 3.3 Installation HRS Series 3-18 HRX-OM-S004 Chapter 3 Transport and Setting Up 3.3.5 Wiring of run/stop signal inputRemote signal input Run/Stop signal input and remote signal input enable the product to operate/stop or switched
HRSH Series 3.2 Installation 3-7 HRX-OM-Q026 Chapter 3 Transport and Setting Up Table 3-2 Amount of radiation and required ventilation Required ventilation amount (m3/min) Heat Differential temp. of 3 oC between inside Differential temp. of 6 oC between inside Model radiation (kW) and outside of and outside of installation area installation area HRSH100-A-20/40Approx.18 305 155 HRSH150-A-
Table 3-2 Amount of radiation and required ventilation Required ventilation amount (m3/min) Heat Differential temp. of 3 oC between inside Differential temp. of 6 oC between inside Model radiation (kW) and outside of and outside of installation area installation area HRS200-A-46-S Approx.37 615 310 Installation at indoor site The products splash-proof specification is IPX4.