90 150 117000 yen reduction Current model IR1000 Series IR2000 Series 100 100 IR1000-A Series IR2000-A Series IR3000-A Series 50 50 0 0 0 10 20 30 40 50 0 10 20 30 40 50 Units used Units used Released into atmosphere IR Special bleeding structure No fixed throttle in the new design.
150 150 150 320 400 70 94 58 65 200 200 480 610 220 220 225 238 Model HAA15 HAA22 B C D E F G H J K L M N P Q R S 1B union union 1 2 B 1 HA AT ID AMG AFF AM Misc. 14-15-3
Please note that if the forced mode is canceled while PROFINET communication with the PLC is established, the input / output data with the PLC will be shown immediately. -90No.EX-OMY0027 (11) To change the Password, log in using Administrator mode and select CHANGE PASSWORD.
Take measures to ensure that water droplets from condensation are not splashed onto any electric parts or equipment. 11. Condensation and freezing of the directional control valve Condensation and freezing may occur in the directional control valve due to the same cause as 10. Condensation and freezing of the pilot port.
ON/OFF signal Ball valve Pressure regulator PB1313A Filter FLUID OUT Air supply source FLUID IN Solenoid Meter-out valve Circuit example 11 7.
(Take care not to scratch the O ring groove. > Step 3 O-ring Installation surface of the O-ring Body Remove the outer seal O-ring from the Body (Take care to prevent the mounting surface of O ring from being damaged ) 11 XL-OMO0001-A 6-3. Assembly Procedure Step 1 Step 2 O ring groove Clean cloth Valve Ethanol Assemble parts eliminating any dust or debris.
Specifications 1 11 / 17 FGX-OM-F001-A 3. Specifications Table3-1 Specifications Item Specifications Fluid Hydraulic fluid: Oils below are applicable.
For detailed description of the signals, refer to the following pages. 15 (2) Internal circuit (Numbers in brackets indicates the pin numbers) (5) PWR_DC24V LF (6) PWR_GND Output signal GND (9) CTR (10) CYL (11) VAL (16) RF (17) PWR Max.
JMHZ2-16D mm 16 MPa 0.1~0.7 (oC) -10~60 (mm) 0.01 (c.p.m.) 120 32.7 (N) 43.5 (mm) 10 (g) 128 3 4M40.7 8 3.4 8 2 11 - 4-2.3 V114-5LU (oC) -1050( (ms) ON5 OFF4 Hz 20 / m/s2 150/30 V114-5LU L (L) (V) 24 -1010% 0.4 (W) [0.40.1] P .1367 LED 300 12 - 4-3.
(If this terminal plug is not used, COM LED of GW unit does not light on.) 11. Waterproof cap Mounted on unused ports of GW unit, input block, power block and output block. The proper use of this waterproof cap can achieve IP65/67 Enclosure. (The waterproof caps are delivered together with each as accessories.)
Output indication mode [Output Ratio] Setting range : -100 to 100% Min. increment : 1% Indicated content: Thermo module output ratio (Ex.: -73%) O u t p u t R a t i o Function: Indicates Thermo module output ratio with M O D E < 7 3 % increment of 1%. + is not indicated but + means heating and means cooling. 11.Upper/Lower Temp.
DRail mounting Direct mounting 20D-A7H/A80H D-A73C/A80C D-F7BAL/F7BAVL D-F7/J79 D-F7V/J79C D-F7W/F79F D-F7WV D-J79W D-M9 D-M9V D-F9W D-F9WV D-F9BA D-A7/A80 D-A79W D-A9 D-A9V Bore size (mm) A 9 13 11 13.5 B 6 8.5 11.5 14.5 A 9.5 13.5 11.5 14 B 6.5 9 12 15 A 6.5 10.5 8.5 11 B 3.5 6 9 12 C 8 12 10 12.5 D 5 7.5 10.5 13.5 C 12 16 14 16.5 D 9 11.5 14.5 17.5 C 11 15 13 15.5 D 8 10.5 13.5 16.5 32
L/min (ANR) 11 M5 x 0.8 3 42 R1/8 65 52 R1/8 130 53 R1/4 130 73 R1/4 200 Symbol Port size Max. flow capacity L/min (ANR) 3A 4 30 4B 6 65 5C 8 130 7D 10 200 Male thread type One-touch fitting type Symbol Applicable tubing O.D.
DRail mounting Direct mounting 20D-A7H/A80H D-A73C/A80C D-F7BAL/F7BAVL D-F7/J79 D-F7V/J79C D-F7W/F79F D-F7WV D-J79W D-M9 D-M9V D-F9W D-F9WV D-F9BA D-A7/A80 D-A79W D-A9 D-A9V Bore size (mm) D 8 10.5 13.5 16.5 C 11 15 13 15.5 D 9 11.5 14.5 17.5 C 12 16 14 16.5 D 5 7.5 10.5 13.5 C 8 12 10 12.5 B 3.5 6 9 12 A 6.5 10.5 8.5 11 B 6.5 9 12 15 A 9.5 13.5 11.5 14 B 6 8.5 11.5 14.5 A 9 13 11 13.5 32
Wiring 1) Pass them through the cable (7) in the order of cable ground (4), washer (5), rubber seal (6), and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note) Cable (7) external: 6 to 8 mm 3.
Wiring 1) Passing through the cable (7), cable gland (4), plain washer (5), rubber seal (6) in this order, and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11). Note 1) Tighten within the tightening torque of 0.5 Nm 15%.
Ground 4-7-11 12 Series VT317 How to Use DIN Terminal 1.
Refer to pages 5-11-2 to 6 for Safety Instruction and Solenoid Valve Pilot pressure (MPa) Caution 1. Lubrication Use turbine oil Class 1 (ISO VG32). 2. Refer to Best Pneumatics Vol. 3 regarding piping, air quality, operating condition and 3 position closed center.
6 Series VH Dimensions: Body Mounted VH600-06/10 2 (A) 4 (B) 32 1 (P) 132 152 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 4-11 132 300 223 M15 x 1.5 15 151 150 48 25 4-Rc 3/4, 1 3 (R) 40 5-8-12 7 Hand Valve Series VH Dimensions: Panel Mounted VH21-02 VH31-
Specifications Bore size 20 to 63 (3/4" to 2-1/2") Piston speed (no load) 59.1 inch/s (1500 mm/s) Note 1) When operating this cylinder at high speed, a shock absorber must be provided. 11 Series NCY3B Made to Order 3 Please contact SMC for detailed specifications, lead times and prices.