Lubrication Equipment Mounting orientation is Upper direction Model Port size Rc(PT) 63 63 80 85 90 100 B C A INA-11-402 INA-11-403 INA-11-404 INA-11-405 INA-11-406 INA-11-407 1/4 141 164.5 170 180 230 251 15 15 15 20 22 22 3/8 1/4, 1/2 3/8, 3/4 3/4, Bracket dimensions Model Port size B C D E A 1 F 345 419.2 K 57 49.6 J 14 14 H 95 120 G 32.5 0 1 1 1 1 2 4, 1 2, 1 175 250 175 250 87.5 125 460 613 135 209 4, 3 ALD600
D 00 Without subplate 1% 0.5% + -0.5% M5 M5 0.007 00 Without subplate B M5 M5 0.28 01 18 0.41 2.5% 1% + -1% Base Mounted Type 00 Without subplate 2 01 18 0.9 02 14 1.4 00 Without subplate 02 14 2.0 3% 1.5% + -1% 4 03 38 3.3 04 12 3.9 A M5 M5 0.28 1 01 18 0.9 02 14 1.4 2.5% 1% + -1% Wiring: The use of three-core screened cable is strongly recommended with the screen earthed at the end away
L 60.5 3 48 2 85.5 5 73 4 110.5 7 98 6 135.5 9 123 8 160.5 11 148 10 185.5 13 173 12 210.5 15 198 14 235.5 17 223 16 19 248 18 20 VS 260.5 285.5 21 273 No.
Do not scratch or gouge the sliding portion of the piston rod. Damaged seals etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of the body and the plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance. 5.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise. x Opening of the initial exhaust valve (valve S) When the pilot pressure is applied to the pilot port S, the valve S is removed from the valve S seal assembly, and the valve opens the adjusted amount.
QW RW T W X Y Z Bore size (mm) S 140 32 60 33 19 157 33 10.5 7.5 40 84 35 180 21 187 39.5 11 8 Long Stroke X Y Z Bore size (mm) Stroke range (mm) 32 125, 150, 175, 200, 250, 300 45.5 12.5 12.5 40 125, 150, 175, 200, 250, 300 55 14 14 8-27-9 10 Series CXT Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height Reed switch Solid state switch A B W D-A9 D-M9 D-F9BAL
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not apply heat cycle.) Operating fluid temperature 0 to 100C (Not be frozen. Do not apply heat cycle.)
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
The pump might be broken as well. 14 Nm). Integral time Communication parameter Sets control mode.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (490 m/s2) while handling. Although the external body of a switch (switch case) may not be damaged, the switch inside could be damaged and cause a malfunction. 2. Do not use until you can verify that equipment can operate properly.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
53 48 34 14 13 NAKM4000 14 38 70 54 42 18 15 Courtesy of Steven Engineering, Inc. !
If there is any doubt about anything specified in Scope and "Content, it shall be resolved by agreement between the customer and SMC. 14 - Revision A How to Order display content correction, etc. URL http://www.smcworld.com 4-14-1 Sotokanda, Chiyoda-ku, Tokyo 101-0021, Japan Tel: 03-5207-8271 Fax: 03-5298-5361 2021 SMC Corporation All Rights Reserved 15 -
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be assimilated, which results in the generation of a lateral load that can cause malfunction.
(Do not change.) OFF OFF When connecting to a MECHA TROLINK-I network, turn OFF pins 1 and 2.
T-slots l Model Bolt Max. tightening torque Nm Max. screw-in depth (l mm) LXP M5 x 0.8 7.4 8.5 Use bolts at least 0.5mm shorter than the maximum screw-in depth, so they do not touch the body.