Check Valve Series AK To install/remove the Flow Control Equipment, tighten/loosen at wrench flat B as close to the thread as possible using the appropriate wrench. Do not apply torque at other points as the product may be damaged. Rotate Body A manually for positioning after installation. 1. Check that the lock nut is tightened. A loose lock nut may cause actuator speed changes. 2.
Standard Strokes Bore size [mm] Standard stroke [mm] 12, 16 5, 10, 15, 20, 25, 30 20, 25, 32, 40 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 50, 63, 80, 100 10, 15, 20, 25, 30, 35, 40, 45, 50 Intermediate strokes are available as a special order.
Parts Purpose Connect to DeviceNet line with an accessory connector for DeviceNet ( ). 10 1 Communication socket (BUS) Input unit 1 connector 2 inputs type ( ) Supplying power for output instruments such as a solenoid valve with an accessory connector ( ). 11 2 Power supply socket (PWR(V)) Supplying power for controlling GW and for input instruments such as a sensor with an accessory connector
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
Install an air filter near this product on the supply side. Select a filtration degree of 5m or less. 2. Compressed air containing a large amount of drainage can cause malfunction of this product and other pneumatic equipment. As a countermeasure, install an after-cooler, air dryer or water separator, etc. 3.
This seat is available as an option for high temperature applications or specific gas applications, such as N2O or CO2. [PEEK] Polyetheretherketone. This material has excellent heat, fatigue and chemical resistances as thermoplastic resin. This seat is available as an option for the regulators. [Viton] Trademark of DuPont Fluoro-rubber (FKM).
CX Model Intermediate stroke Standard stroke (mm) Symbol Specifications As for the intermediate strokes (by the 5 stroke interval) other than the standard strokes at left are manufactured by means of installing a spacer with the width of 5, 10, 15, 20, 25 mm. Example) In the case an MGF63-15 specification is required, a spacer of 15 mm is installed in the MGF63-30.
If using in an environment that is exposed to water splashes, please take measures such as using a cover. If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction etc.).
The position of spanner should be a root as close as possible to R thread. Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
This allows reading and monitoring the contact signal from an external switch. When inputting an external switch signal to the contact input, select External Switch (external switch signal) for the type of contact input signal. (Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.
Applicable model A B C D E F G H J L t AS-10D ZH05/07/10DA 11 18 3.5 3.4 18.2 23.2 45 6.2 11.2 14 1.6 AS-25D ZH13/15DA 17 25.8 4.4 4.5 22 27 20 AS-30D ZH18/20DA 22 30.8 27.2 32.2 22 231 ZH Series Circuit Examples Caution Handling of Circuits Select the related air preparation equipment with applicable size in reference to the circuit example below.
requirements for machinery, as applied to industrial machines e.g. machine tools, injection molding machines and automatic machines.
Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as magnet grippers. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 40 - 4.
Never turn the connector as it is not designed to turn.
Be sure to connect the load to the rod end with the cylinder in an unlocked condition. If this is done when in a locked condition, it may cause damage to the lock mechanism. 1. Do not perform unlocking when an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly. Take the following steps. CL CL1 2.
Grease pack part no.: GR-S-010 (10 g), GR-S-020 (20 g) Air-hydro Kit no.
Lightning surge countermeasures should be applied directly to system components as necessary. 2. Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1.
For connection with a load having an external support/guide mechanism, select an appropriate connection method and perform careful alignment.