SI unit for EtherNet/IP TM NOTE D class grounding (with the ground resistance of 100 ohm or less) should be performed for ground terminal, and ground at one point. -13No.EX-OMK0004-B Pin layout and connection diagram of power supply connector cable (unit: mm) Model No.: EX500-AP-S (Refer to page 31.) Pin No.
Mounting accessories (option) 2) Auto drain Assembly (Option Symbol: D) (1) Mount a nipple with sealant and an auto drain onto the drain valve. * When auto drain is used, put the after cooler body onto a mounting bench. If Option S has not been ordered, it can be provided as a separately sold part.
Squeezing or twisting of the tubing that is connected d. Hardening or deterioration of the tubing that is connected e. Air leakage 8 Doc. no.IZ*-OMX0012-B 1. How to Order 1-1. Ionizer IZG10 08 01 01 Ionizer Gun One-touch fitting Nozzle type Symbol Applicable tube O.D.
D Shows how precisely the pressure can be indicated or set by the digital Pressure switch. When 1 digit = 1 kPa, the pressure is given with an increment of 1 kPa, e.g., 1, 2, 3, , Digit (min. setting unit) 99, 100. F Fine adjustment mode See "Fine adjustment of indicated value". Abbreviation of full span or full scale which means the max. fluctuation range.
Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e. Avoid using in an atmosphere where there are particles, conductive iron powders, oil mist, salt, solvent, blown dust, cutting oil (water, liquid), etc. f.
D-A9, M9, M9W, M9AL are shipped together (but not assembled).
(Or None in the Case of No Switch), Lock Unit Built-in Magnet: D (Built-in)
(Or None in the Case of No Switch), Lock Unit Built-in Magnet: D (Built-in)
(Or None in the Case of No Switch), Lock Unit Built-in Magnet: D (Built-in)
Magnet: D (Built-in), Mounting: G (Rear Flange), Tube: 125~160 Aluminum (with or w/o magnet);180~200 Steel (w/o magnet),Aluminum (w/magnet);250 Steel, Bore Size: 125mm, Thread: TN (NPT), Stroke: 250mm, Option: Cushion at Both Ends, Cylinder Switch Type: M9PW--Solid State, 2-color Indication, 3 Wire PNP, Horizontal, Lead Wire or Pre-wired Connector: 0.5m Lead Wire (Or None in the Case of No
D Blue (BU) Fixed end MS Translucent (N) LQ Fluid Air MQR Burst Pressure Characteristics Curve and Operating Pressure Max operating pressure (at 20C) 0.8 MPa T One-touch fittings Applicable fittings 10 18 24 30 36 Min. bending radius (mm) 5 Refer to the burst pressure characteristics curve.
Feedback circuit (VEA252 only) P/I/D adjustment NULL adjustment Warning Integrator cicuit Driving circuit Voltage comparing circuit Electro-pneumatic proportional valve GAIN adjustment 1. A negative SIGNAL terminal or a negative SENSOR terminal cannot be connected in common with the negative 24 VDC power supply terminal. 2.
Fittings & Tubing Air Cylinders Rotary Actuators How to Order Clean series 10 11 Relief type Vacuum suction type Nil Built-in magnet No D With auto switch (Built-in magnet) 10 C D M 2 X L 40 150 Z M9BW Low speed cylinder Mounting Basic (Double-side bossed) Axial foot Rod flange Head flange Boss-cut, Basic Boss-cut, Rod flange B L F G BZ FZ Auto switch Nil Without auto switch For applicable
Port type Rc NPT G Nil TN TF Bore size (mm) Auto switch mounting bracket Note) Note) This symbol is indicated when the D-A9 or M9 type auto switch is specified. This mounting bracket does not apply to other auto switches (D-C7 and H7 , etc.)
K ML1C 25, 50, 75, 100, 125, 150, 200 201 to 350 D25 32 40 301 to 400 301 to 450 301 to 800 25, 50, 75, 100, 125, 150, 200, 250, 300 -X Intermediate stroke is available, too.
Standard stroke -X Bore size (mm) Standard stroke (mm) Piping port location 15, 32 100, 150, 200, 250, 300, 350 400, 450, 500, 600, 700 Operating direction: Right Operating direction: Left Operating direction: Right Operating direction: Left Operating direction: Right Operating direction: Left Operating direction: Right Operating direction: Left a b c d e f g h 20Nil Note 1) Please consult
Standard Strokes Bore size [mm] Standard stroke [mm] 1 20 25, 50, 75, 100, 125, 150, 200, 250, 300 25 32 40 1 Intermediate strokes not listed above are produced upon receipt of order. The minimum stroke is 25 mm. Mounting Brackets/Part No.
With the use of D-sub output blocks, a maximum of 9 remote D-sub manifolds can be attached to one EX600 communication module. This serial interface is compatible with series SV1000/2000/3000, VQC1000/2000/4000, S0700 and the new SY series valves.
With the use of D-sub output blocks, a maximum of 9 remote D-sub manifolds can be attached to one EX600 communication module. This serial interface is compatible with series SV1000/2000/3000, VQC1000/2000/4000, S0700 and the new SY series valves.
Magnet: D (Built-in), Mounting: D (MP2, Detachable Rear Clevis), Bore Size: 250 (2 1/2"), Stroke: 0600 (6"), Air Cushion: Both Ends (Air Cushion), Adjustment Range: Not Applicable, Auto Switch: No Switch, Lead Wire or Prewired Connector: N (No Lead Wire), Number: 2 pcs. (Or None in the Case of No Switch), X Option: XB9 [Low Speed Cylinder (10~50mm/s)]