Air Cylinder RSQ Series Stopper Cylinder Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Operating Environment Warning (1) Do not operate under the conditions listed below due to a risk of malfunction. In locations having corrosive gases, organic solvents, and chemical solutions, or in locations in which these elements are likely to adhere to the equipment. In locations in which salt water, water, or water vapor could come in contact with the equipment.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Red flashing SI unit has detected the transmission rate, but is not addressed by the DP master OFF Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not connect the terminating resistor outside, when the setting switch for the terminating resistor is ON. (4)How to connect.
. * Options are shipped together with the product but do not come assembled. 9 2-Color Display Digital Flow Switch RoHS PF2M7-L Series How to Order Integrated display Made to order (Refer to page 26.)
Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Do not use with pressure or temperature beyond the specification range.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
The VQ20/30 series is a pilot operated, two port multi-media valve. The series is compact and lightweight with a large flow capacity. The VQ20/30's long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.Manifold for VQ20/30 pilot operated valve
For the auto switch mounting rail, do not remove the pre-equipped rail. Since the mounting thread is drilled through inside a the cylinder, it will result in air leakage. MVGQ For basic style, the port position in a head cover is available either perpendicular to the axis or in-line with the cylinder axis.
Do not immerse the cylinder in water or chemicals. When the cylinder is operated in a condition with water pressure, the fluid leaks into the cylinder in the early stages. In the worst case, the fluid may back flow inside the piping and damage the solenoid valve. Maintenance Warning Mounting 1.
However, do no rotate the cushion valve exceeding two turns, and do not rotate the speed controller valve exceeding four and half turns (40: maximum two turns). If 0.6 Nm or more of torque is applied, the valve may become loose and may jump out depending on the amount of air pressure. Cushion Adjustment The air cushion is built in on the head end for the CK1 series.
Do not disassemble the power clamp No special maintenance is necessary because the power clamp has a fully enclosed design to protect the clamp against welding spatter, and also the power clamp has a contamination resistant construction. Do not disassemble any parts other than replaceable parts, otherwise it may reduce the performance of the clamp cylinder. 3.
Also, do not attempt to tighten the bumper bolt without using a nut. If the dumper bolt is removed, the piston hits the head cover causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3.
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.