HEC-OM-S008 Name Alarm flag 1,2 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit Name Explanation 0 Unused 1 ERR01 System error 1 2 ERR02 System error 2 3 ERR03 Back-up data error Alarm flag 1 4-10 Unused 11 ERR11 DC power supply failure 12 ERR12 Internal temperature sensor High temperature failure 13 ERR13 Internal temperature sensor Low temperature failure 14 ERR14 Thermostat alarm Alarm given off status
(Refer to Table 11 (P21)) Before mounting a support bracket, make sure the product is aligned by placing on the leveled surface. It is recommended to secure the mounting screws temporarily to insure alignment before tightening with the specified torque. Fig 3. Order for tightening mounting screws 11 2-10.
Piping 11 10. Operating Environment 12 11. Speed Control 12 12. Clean Series / Precautions 13 13. Troubleshooting 17 14. Auto Switch 18 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
11 DC12V DC24V DC12V24V CEU5 CEU5 MODE 2 90 CEU5 4 10,11 SMC 13 CEU5 13 23m 23m () CEU5 11 AC 10 70500mm/s 12 6-2 5,6, 12 5 5,12 10 ?
Slider type LEKFS series . 7 2.1 Specification . 7 2.2 How to Order . 9 2.3 Construction . 11 3.
It will cause failure or malfunction. 11. Do not use the product in an area where a magnetic field is generated. It will cause failure or malfunction. 12. Do not install the product in an environment containing flammable gas, explosive gas, or corrosive gas. It could lead to fire, explosion, or corrosion. 13.
ID 2 3 3 2 4 2147483647 0.01mm 4 1 5 0 6 H 2 065500 mm/s 7 L 8 H 2 0300 % 9 L 10 3 ID1 11 2 4 2147483647 0.01mm 12 1 13 0 14 0255 15 0255 4 16 0255 17 0255 18 IF(ID=1) 19 ID2 2039 ID1 ID3 4059 ID1 ID4 6079 ID1 ID5 8099 ID1 ID6 100119 ID1 ID7 120139 ID1 ID8 140159 ID1 33 - / Bit No.
Note 3) Station numbers are started from D side although connector is mounted on D or U Side. 11 VFR3000-OMH0003-B TROUBLE SHOOTING (14) Excessive supply oil amount (11) Intrusion of foreign matter Wrong Pressure supplied X port.
End plate R (Output block side) How to order 11. Waterproof cap Mounted on the unused ports of the Input block, Output block and Power block. Proper use of this waterproof cap can achieve IP67 enclosure. (The waterproof caps are delivered together with the Power block as accessories.)
Note 5) M and MO type connectors cannot be selected for the model with the pressure sensor or the pressure switch for vacuum. 11 - Doc. no.
Terminal No. 2 4 6 8 10 12 14 16 18 20 Output No. 1 3 5 7 9 11 13 15 24 V Type +COM EX510-S102 Terminal No. 1 3 5 7 9 11 13 15 17 19 Output No. 0 2 4 6 8 10 12 14 0 V Type + + + + + + + + -COM Terminal No. 2 4 6 8 10 12 14 16 18 20 Output No. 1 3 5 7 9 11 13 15 0 V Type + + + + + + + + -COM : Only a flat cable type manifold (P kit) can be connected to EX510-S 02 .
Solenoid valve (11) SYJ319Plate assembly (12) XL1AV16-90-2 63 80 Valve size Description Part indication No. Solenoid valve (11) SYJ519Plate assembly (12) XLAV63-90-1 Note 1) The at the end of the solenoid valve part number is the selection symbol for voltage, electrical entry, and other specifications. For details about selection symbols, refer to the Web Catalog.
On : Output Off : Not output On, Off Off 11 Upper/Lower Temp. Alarm Sequence * How to return default value: Turn on the power supply with pressing [SEL] and [RET] keys.
Insulation failure (interference with other circuits, poor insulation between terminals, etc.) could introduce excessive voltage or current to the controller or its peripheral devices, causing damage to them. 11. The speed and force may change depending on the cable length, load, and mounting conditions.
Replace pilot valve assembly. (10) Protect the valve so that water does not splash the coil. (11) To remove foreign matter,air blow piping, then replace valve.
Mounting of standard auto switch 11 Standard Auto Switch Mounting The standard auto switch cannot be used in a magnetic field environment. For information on our cylinders that can be fitted with a magnetic field resistant auto switch, please refer to page 9.
No.EX-OMP0013-E PRODUCT NAME SI unit for EtherNet/IPTM MODEL / Series / Product Number EX260-SEN# Table of Contents Safety Instructions 2 Model Indication and How to Order 8 Summary of Product elements 9 Definition and terminology 10 Installation and Wiring 11 Installation 11 Wiring 12 LED Indication and Settings 16 Hardware configuration 19 EDS file and icon 19 Setting using RSLogix5000TM
29.5 31 25 11.5 14 16.5 26 28.5 7.5 10 12.5 30 32.5 32 12 13 15.5 25 27.5 8 9 11.5 29 31.5 40 15 20 20 32 32 11 16 16 36 36 50 14.5 21 21 33 33 10.5 17 17 37 37 The value of W in the table means the amount of auto switch protrusion from the body end surface.
Fittings & Tubing Air Cylinders Rotary Actuators How to Order 11 Vacuum suction type Clean series 11 M D H R 3 10 R M9B S 22 M D H R 3 10 R M9B S Copper, fluorine and silicone-free + Low particle generation Number of auto switches 2 pcs. 1 pc.
Applicable cylinder ML2B25 ML2B32 ML2B40 MY-S25A M6 x 1 35 50 8 5 9.5 5.5 B MY-S32A M8 x 1.25 45 64 11.7 6 11 6.6 B Guide for Side Support Application For long stroke operation, the cylinder tube may be deflected depending on its own weight and the load weight. In such a case, use a side support in the middle section.