Series PF2W Digital Flow Switch For Water White OUT2 FLOW SWITCH U P U Blue DC() SET 34 60 50 12 to 24 VDC OUT2 OUT1 DOWN FOR WATER -67 PNP (2 outputs) Brown DC(+) 34 2 x Port size 4 x 4.5 50 40 Black OUT1 + Load U White OUT2 (42.2) U Blue DC() 12 to 24 VDC Connector pin numbers 4 3 77 2 1 Pin no.
u r u r t r t i i e Drain AW20(K) t w i y Drain q AW20K to AW60K (Filter Regulator with Backflow Function) IN OUT u A-A o Drain A r t i SMC K P C U O S L H o t A Drain Component Parts No.
O ut put area I nput area W o rd d ata area In p u t w o rd d ata Rem arks W o rd d ata area O u tp u t w o rd d ata Rem arks RW w 0 b15, b14, b1, b0 b 1 1b 0100% F.S. RW r0 b15, b14, b1, b0 b 1 1b 0100% F.S. RW w 1 U nused RW r1 U nused RW w 2 U nused RW r2 U nused RW w 3 U nused RW r3 U nused O ut put dat a occupi es 4 w ords, but uses onl y t he 1st w ord act ual l y.
M O U N T I N G S Full range of NFPA accessories.
M O U N T I N G S Full range of NFPA accessories.
7 @2 @3 @4 r y e #7 u o !1 i w !8 #4 !6 A @0 @1 !9 #2 !0 #1 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com A Ball bushing bearing #5 @5 #0 @6 @8 !7 !3 #8 !2 @1 !
Special resin Carbon steel Description No. q w e r t y u i o !
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
T h e r e i s n o p a r t i c u l a r p r o b l e m i n u s i n g t h e s y s t e m . R e a d t h e i n s t r u c t i o n m a n u a l W i l l y o u d o a t h o r o u g h l y f o r t h i s i t e m a n d c o u n t e r p o s i t i o n i n g m o t i o n ?
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
C a u t i o n Piston speed should be controlled gradually from low speed with a speed controller fully closed to the specified speed. 2-6. Cushion C a u t i o n Cylinder cushions are adjusted properly before shipping, re-adjust the cushion valve on the cover according to the load and the operating speed.
of poppet valves u close due to the balance between actuating forces F1 and F2.
For type R, U, DC voltage is only available. Power saving circuit is only available in the "Z" type.
U U U O O O O S S S S H H H H L L L L to to to to Possible to change to the optional mounting angles.
: 2 to 10 stations U side: 2 to 10 stations Nil Standard length (Specify a longer rail than the standard length.)
The U-phase and V-phase currents must be adjusted so that they balance. Repeat the adjustment alternately between them several times. Repeat the operations of steps 4 to 6 (phase-U and-V alternately) until adjusting the offset amounts both for phase-U and -V in both directions cannot reduce the torque ripple any more. Then, perform the same operation by adjusting by smaller amount.
HNBR POM, Stainless steel Note) u u Seal Cassette NBR POM, Stainless steel (1) i i O-ring Seal NBR NBR o o O-ring O-ring NBR NBR !
U Approx. U A B B A D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U SMC SMC Approx. U B A B A Approx. U D-A73C D-A80C D-J79C D-A7*C,D-A80C Approx. U Approx. U D-A7*C,D-A80C A B A B Approx.
U B A Approx. U A B D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U Approx. U Approx. U SMC SMC Approx. U A B B A Approx. U D-A73C D-A80C D-J79C B A A B Approx.