XLGR Series Bonnet assembly (Construction part no.) 1 Valve size Temperature Specifications 80 100 160 For general environments XLG80-30-1-1 XLG100-30-1-1 XLG160-30-1-1 For high temperature XLG80-30-1H-1 XLG100-30-1H-1 XLG160-30-1H-1 Note1) The magnet for auto switch is not provided. When the magnet for auto switch is necessary, add -M9// at the suffix of the part number.
Tightening torque for piping Connection threads Proper tightening torque Nm Lubrication 1/8 7 to 9 1/4 12 to 14 Caution Caution Caution Caution 3/8 22 to 24 Lubrication 1)The valve has been lubricated for life at the factory, and does not require any further lubrication. 2)In the event that it is lubricated, use class 1 turbine oil (without additives), ISO VG32.
Elliptic Response speed The suction flow rate of the ejector or the pump, which is used for calculating the response speed.It is to of the maximum suction flow rate. To be used when adsorption surface of work is not horizontal. Average suction flow rate Ball joint type 1 2 1 3 A pad with a low electrical resistance that is used as an electrostatic prevention measure.
It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below. For standard installation, turn 15 to 30 using tool, after fastening by hand. Pay attention not to over torque the product.
Limited warranty and Disclaimer/Compliance Requirements The product used is subject to the following Limited warranty and Disclaimer and Compliance Requirements. Read and accept them before using the product. Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,whichever is first.
Brown Brown Load Load Switch 1 Switch 1 Blue Blue Brown Brown Switch 2 Switch 2 Blue Blue Power supply voltage Voltage drop Leakage current Load impedance Load voltage at OFF = x 2 pcs. x Load voltage at ON = x 2 pcs. = 1mA x 2 pcs. x 3k = 6V Example: Load impedance is 3k Leakage current from switch is 1mA = 24V 4V x 2 pcs. = 16V Example: Power supply is 24VDC Voltage drop in switch is
VVZS3000-4-1 VVZS3000-4-2 18 x 15 x 1.5 7.5 x 4.5 x 1.5 VVZS3000-5-n (1) Seal B Seal A NBR NBR NBR NBR Carbon steel Carbon steel w e O-ring O-ring r t Tie-rod y Tie-rod for station addition VVZS3000-5-1-1 (2) Note 1) n: Stations Note 2) Manifold block assembly is attached with tie-rod for increasing stations. Assembly part no.
S (1 auto switch) is shipped with a righthand auto switch. Nil (2 auto switches) is shipped with a right-hand and a left-hand switch.
Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
This is applicable only when multiple Thermo-cons are used. (Unit number 1 to F is vaild when used the Modbus communication) 3.
Though an accurate ajustment is possible by wear-out situation of needle,precence of dielectric thing and potential level of GND in the installation location 9. Frequency selecting switch...Select frequency at pulsed DC mode. No 0-1Hz 1-3Hz 2-5Hz 3-8Hz 4-10Hz 5-15Hz 6-22Hz 7-33Hz 8-5 6 7 ; < = : 9 8 Generate only plus ion 9-Generate only minus ion 6.
(mm)
ERR01 System error 1 Stop The key functions are as follows: Shows output ratio of thermo module by 1%. The prefix symbol stands for cooling and no prefix stands for heating. -100 to 100% 9 Output Ratio (1%) [SEL]: Used to show the item that needs to be Move the product to an environment with little noise, turn ON the power supply. If there is no alarm, it was caused by noise.
A guide for the additional tightening is 1/6 to 1/4 turns. But in case of the brass sleeve, the limit for additional tightening is 1/2 turns. When there is a leak even after additional tightening, replace the sleeve with new one. (5) Sleeve is not recyclable.
Note) O-rings cannot be shipped as a single unit. 4 1 PVQ 8 3 3 A B 2 1 Body ported Base mounted 2 1 VY1 4 3 5 VBA VBAT 1 1 2 1 1 4 1 7 1 4 1 AP100 1 2 9 2 Without sub-plate 8 1 2 4 1 Option (2) Part no.
Also, when the sealant tape is used, leave approx. 1 thread ridges exposed at the end of the threads. Connection Female Thread: G Uni thread size Wrench tightening angle after hand-tightening [deg] Tightening torque [Nm] 1/8 30 to 45 3 to 4 1/4 15 to 30 4 to 5 3/8 15 to 30 8 to 9 1/2 15 to 30 14 to 15 Winding direction Sealant tape Expose approx. 1 thread 2.
Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
the total (n) does not exceed "1". n = 1 + 2 + 3 1 Load factor n 1 = m/m max MX Note Item Review m. m max is the maximum load mass.
Co., Ltd.: NJC-245-PF UL CSA Female connector 1 2 3 4 5 Female connector 6 7 8 9 Alarm output connector D-sub 9 pin (male type) M Communication connector Hirose Electric Co., Ltd.: CDE-9S Holding screw M2.6 Fitting connector: CDE-9P or equivalent Pin No.
Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.