EXxx-OMO0027 (When L/A IN LED is OFF.) (2)Check that the connectors of L/A IN and L/A OUT communication cables are connected and there are no broken wires. L/A IN and L/A OUT LEDs are OFF.
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
(Refer to page 42 the section "Setting and Adjustment" for details.) -14No.EX-OMU0028-D Definition and terminology Term Definition 100 100BASE-TX Standard LAN transmission line with communication speed of 100 Mbps. B Base A unit which establishes wireless communication of input or output data to the remote. It is connected to a PLC to establish communication of input or output data.
A [mm] Weight [g] 01 50 mm IBG1-12-10-50 57 35 02 100 mm IBG1-12-10-100 107 40 03 150 mm IBG1-12-10-150 157 45 04 300 mm IBG1-12-10-300 307 59 11 Long nozzle with a silencer Long nozzle 50 mm IBG1-12-10-50S 72 57 12 100 mm IBG1-12-10-100S 122 62 13 150 mm IBG1-12-10-150S 172 67 14 300 mm IBG1-12-10-300S 322 81 Long nozzle Long nozzle with a silencer IBG10_11/With fitting Symbol Type Applicable
Allowable kinetic energy 40 50 63 80 100 Air cushion 2.8 4.6 7.8 16 29 Allowable kinetic energyJ Non cushion 0.33 0.56 0.91 1.50 2.68 Rubber bumper 1.8 3.6 6.0 12.0 12.0 C a u t i o n When the product is equipped with a rubber bumper, note that there will be a slight bounce at the stroke end. 2-7.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
AD27-6-A With bowl guard AD27-6C-A AD37m-6-A AD47m-6-A Normally open (N.O.) With bowl guard AD38m-6-A AD48m-6-A Automatic (Auto drain) Manual With drain cock C2SF-2-A C3SF-2-A C4SF-2-A With level gauge C3LF-8-A C4LF-8-A With drain guide (without valve function) C2SFm-2J-A C3SFm-2J-A C4SFm-2J-A With level gauge C3LFm-8J-A C4LFm-8J-A Metal Normally closed (N.C.)
B A B A A A A A A 2.PUSH 2.PUSH B B B B 1.TURN 1.TURN VQZ 28 5.5 35 74.5 SMC VQD 13 2-M4 clamp screw EXH outlet M5: External pilot port 9 D side U side Stations 1 2 3 4 5 6 7 8 n C8: 3(R) port Lead wire length: L0, 600 mm L1, 1500 mm L2, 3000 mm C8: 1 (P) port 9 For top ported 4 4 4 4 4 4 4 4 R 3 60 37 26 (49.5) 2 1 2 2 2 2 2 2 2 P 29.5 13 7.5 P = 11.5 44 29.5 2n-C3, C4, C6, M5 (4(A),
Caution : CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
When a filter element is used repeatedly, clean it with air blow or wash it with a neutral detergent. (For 40 m, For 80 m) Check the condition of the element and replace the element with a new one when the specifications are not satisfied.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
A maximum of input waveform shall be 100 kHz, and the waveforms of A and B phases at this time are as below. +12V 10% Channel A "A-phase pulse" Channel B +12V 10% "B-phase pulse" B C D A E F G H : requires 2.5sec or more : requires 5sec or more : requires 2.5sec or more : requires 5sec or more : requires 2.5sec or more : requires 5sec or more : requires 2.5sec or more : requires 5sec
Grounding should be to a type 3 ground. (Ground resistance of 100 or less.) 3. Use a wire with a sectional area of 2 mm2 or larger for grounding. Grounding should be as close as possible to the controller, and the ground wires should be as short as possible. 4.
Use a soft cloth to remove stains.
When using a rod boot, a stroke range of up to 1000 mm is available. Please consult with SMC when exceeding a 1000 mm stroke.
Fluororubber is used for rubber seal materials. 80 IR 0 Ozone resistant X170 IR 0 Compatible with modular connection brackets Modular Combination Example Description Applicable model IR100--X170 AF20-A AFM20-A Y200-A Y200T-A IR20--X170 AF30-A AFM30-A Y300-A Y300T-A IR30--X170 AF40-A AFM40-A Y400-A Y400T-A qRegulator wAir filter eMist separator rInterface tInterface with bracket Note 1) The
/ 100 ft@125 KHz (max.) 0.50 db / 100 ft@500 KHz (max.) 0.70 db / 100 ft@1 MHz (max.)
6 r A A A A !4 i u q i !4 r y t y !2 o !5 r u t q !5 e i o !2 r Component Parts No. Description Material Note No. Description Material Note Body A O-ring PBT NBR q !3 Elbow body O-ring PBT NBR w !4 Body B O-ring Electroless nickel plated Brass NBR e !5 Body B O-ring Electroless nickel plated Brass NBR r !6 Needle Spacer Electroless nickel plated Brass POM (2) t !