B B B B B B B B B + IN + + +++A IN A NI NI B B O T U O T U 2 4 To CYL port To CYL port P.930 P.931 P.932 P.941 Connector assembly SY3000-37-80AHousing (1 set: 8 pcs.)
to ports (A) and (B), both A and B strokes extend.
CQS A-A' section (Rod side port) B-B' section (Head side port) CQM Spring extend CQ2 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com RQ MU D-X 20A-A' section (Rod side port) B-B' section (Head side port) Rod end male thread Data Replacement Parts Component Parts
SUP block plate VVQ2000-16A EXH block plate VVQ2000-19A Port plug Note 1) A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B C4 (N3) With 4 (5/32") One-touch fitting Side port Cylinder port sizes Fill out in case of mixed sizes (CM/LM/NM).
Type A B C Accessory fittings Clamp fitting L AERSBAN-DSET 100 86 30 clamp A: 2pcs. A 70 AERSBAN-ESET 70 56 clamp B: 1pc. B 45 11 21 11.
Local Area: (800) 258-9200-www.stevenengineering.com Pump chamber B Pump chamber A Check valve Shaft Suction port (FLUID IN) Diaphragm B Diaphragm A Drive chamber A Drive chamber B Control unit 1.
FLUID OUT) Pump chamber B Pump chamber A Check valve Shaft Suction port (FLUID IN) Diaphragm B Diaphragm A Drive chamber A Drive chamber B Control unit 1.
Discharge port (FLUID OUT) Pump chamber B Pump chamber A Check valve Shaft Suction port (FLUID IN) Diaphragm B Diaphragm A Drive chamber A Drive chamber B Control unit 1.
(FLUID OUT) Pump chamber B Pump chamber A Check valve Shaft Suction port (FLUID IN) Diaphragm B Diaphragm A Drive chamber A Drive chamber B Control unit 1.
HED003-W2 A B 13 19 HED003-C2A B (Temperature Controller) HED003-HW13 19 (Heat Exchanger) HED005-W2 A B 13 19 HED005-C2A B (Temperature Controller) HED005-HW13 19 (Heat Exchanger) HED007-W2 A B 13 19 HED007-C2A B (Temperature Controller) HED007-HW13 19 (Heat Exchanger) Keep this manual available whenever necessary.
Option Symbol and Composition Fluid Name and Option Option symbol Seal material Coil insulation type Body, Shading coil material Fluid (Application) Option symbol and body material Brass or BC6 Stainless steel Applicable valve 10A to 50A 10A to 25A F, B L, J B J Note 1) Standard A B C D E F G H J K L N P Q S T NBR FKM Ethyl alcohol Ethylene glycol Caustic soda (25% ) Gas oil Silicon oil
3 A-y A-u A-i A-y B-q B-w B-e B-r B-w B-t B-y B-t Orifice body PTFE seal O-ring Sleeve O-ring O-ring O-ring Name plate O-ring O-ring Orifice body Name plate O-ring O-ring O-ring O-ring Orifice O-ring O-ring Name plate O-ring O-ring O-ring O-ring PEEK resin Special PTFE Special FKM POM Special FKM Special FKM Special FKM Special FKM Special FKM PEEK resin Special FKM Special FKM HNBR Special
3 A-y A-u A-i A-y B-q B-w B-e B-r B-w B-t B-y B-t Orifice body PTFE seal O-ring Sleeve O-ring O-ring O-ring Name plate O-ring O-ring Orifice body Name plate O-ring O-ring O-ring O-ring Orifice O-ring O-ring Name plate O-ring O-ring O-ring O-ring PEEK resin Special PTFE Special FKM POM Special FKM Special FKM Special FKM Special FKM Special FKM PEEK resin Special FKM Special FKM HNBR Special
Then the pressure in the pressure action chamber B falls to open the main valve C.
Then the pressure in the pressure action chamber B falls to open the main valve C.
Then the pressure in the pressure action chamber B falls to open the main valve C. < Valve closed > When the coil o is not energized, the pilot valve A is closed and the pressure in the pressure action chamber B rises and the main valve C closes.
Analog Output Flow/Analog output Output A B C Voltage output 1 V 1.1 V 5 V Current output 4 mA 4.4 mA 20 mA C Model Rated flow [L/min] Minimum Maximum LFE1 0.5 20 LFE2 2.5 100 LFE3 5 200 B A Outside the range 0 Min.
Then the pressure in the pressure action chamber B falls to open the main valve C. < Valve closed > When the coil o is not energized, the pilot valve A is closed and the pressure in the pressure action chamber B rises and the main valve C closes.