SYJ300/500/700 (Value in the initial state) Vibration resistance: No malfunction occurred in one sweep test between 45 and 2000 Hz. Test was performed to axis and right angle directions of the main valve and armature when pilot signal is ON and OFF.
2000 2000 mm B 8m 8 8 B 10m 1.5 m 1 1 A A 15m m 3m 3 3m 3 B B 20m 5 5m 5 C C 5m 3 00 3 00 500 500 600 600 7 00 7 00 800 800 900 900 1000 1000 1 2 00 1 2 00 1500 1500 1800 1800 2000 2000 LEFB16 LEFB16 LEFB25 LEFB25 () R R LEFB32 LEFB32 S S / P.38 5.3 <> NPNPNP LEFS16A-100 NPN -14- 2.4. 16/25/32 40 22 21 1 12 2 13 3 14 4 15 5 16 NBR 6 17 7 18 8 A 19 9 B 20
Acceleration Deceleration Can be set in units of 1mm/s2.
" # $ % $& ' ($ % $& ) Input unit GW unit SI unit VQC1000 2000 4000 SI unit Input unit SV1000/2000/3000/4000 How to Order GW Unit GW Unit DN1 EX500 G Communication protocol DN1 PR1A MJ1 EN1 DeviceNet PROFIBUS DP CC-Link EtherNet/IP 1680 Decentralized Serial Wiring (GW System, 4 Branches) Series EX500 GW Unit Specifications EX500-GDN1 EX500-GPR1A EX500-GMJ1 EX500-GEN1 Model DeviceNet PROFIBUS
(STO switch) S2: Start switch (STO release switch) S3: On switch S4: Off switch KM1: Magnetic contactor K3: Safety relay EMG: Emergency stop switch CN3 EM1 or EM2 M Servo motor Note.
Series NVFR2000 Manifold valve D-Subconnector for 2000 Series Plug-In type -With D sub connector Orientation of D-Sub connector for 2000 Series manifold is parallel with mounting surface. For other manifold sizes the connector receptacle is perpendicular to the mounting surface.
Without release valve Without pressure sensor/switch for vacuum With pressure sensor 30 m/s2 Vibration resistance Note 1) Pilot operated dual 2 port Pilot operated 2 port Valve configuration 20 m/s2 0.3 to 0.6 MPa Operating pressure range With switch for vacuum Poppet seal Valve construction Without pressure sensor/switch for vacuum With pressure sensor 150 m/s2 Impact resistance Note 2)
]*2 20 Impact resistance [m/s2]*3 100 ZL3 ZL6 Branch With valve *1 Values are at the standard supply pressure and based on SMCs measurement standards.
(Value in the initial. stage) Vibration resistance: No malfunction from test with 45 to 2000 Hz one sweep, to axis and right angle direction of main valve, each one time when pilot signal ON and OFF.
Overhang: L3 [mm] 1000 mm/s2 1000 mm/s2 600 3000 mm/s2 3000 mm/s2 Mep 5000 mm/s2 5000 mm/s2 400 10 mm/s2 10 mm/s2 m 200 L3 0 0 5 10 15 20 25 30 35 40 Work load [kg] Based on the above calculation result, the EQFS25A-200 should be selected. 9 Easy to Operate Model Selection EQFSH Series Battery-less Absolute (Step Motor 24 VDC) SpeedWork Load Graph (Guide) Model Selection EQFS H Series EQY
Up to 2000 Up to 600 Up to 800 Up to 1000 Up to 2000 Up to 2500 Up to 3000 Up to 400 Up to 600 Up to 800 Up to 1000 10 20 45 60 Guide Rod Slider High Rigidity Slider Type Step Motor (Servo/24 VDC) AC Servo Motor Belt drive Belt drive Series LEJB Ball screw drive Series LEL Series LEJS CAT.ES100-101 CAT.ES100-104 Sliding bearing Series LEL25M Ball bushing bearing Series LEL25L Series LEJS
20 m/s2 With pressure switch Impact2, 3 resistance 150 m/s2 Without pressure sensor/switch With pressure sensor 100 m/s2 With pressure switch Standards CE marking, RoHS 4 Refer to the Valve assembly on page 32 for the valve model number. 5 ZK2-VAmR: After instantaneous energization of the supply valve (20 ms or more), ON state is maintained without energization.
T1 T2 T3 T4 T1 = V/a1 [s] T3 = V/a2 [s] L : Stroke [mm] (Operating condition) V : Speed [mm/s] (Operating condition) a1: Acceleration [mm/s2] (Operating condition) a2: Deceleration [mm/s2] (Operating condition) P T2: Constant speed time can be found from the following equation.
(initial value) Vibration resistance: No malfunction when tested with one sweep of 45 to 2000 Hz in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states. (initial value) Note 3) Refer to Best Pneumatics Vol. 4 for details on valves. AMJ Misc.
(Values at the initial period) Vibration resistance: No malfunction from test with 45 to 2000 Hz one sweep, to axis and right angle direction of main valve, each one time when pilot signal ON and OFF.
80 mm/s2 Target position 2: Travel distance 5 mm, Travel speed 20 mm/s, Acceleration 80 mm/s2, Deceleration 80 mm/s2 ii.Calculation example Travel distance [Number of pulses (pulse)] = Travel distance (mm) Encoder resolution (m/pulse) Travel speed [Pulse frequency (pulse/s)] = Travel speed (mm/s) Encoder resolution (m/pulse) Acceleration and Deceleration time [s] =Travel speed (mm/s) /
Type (SQ1000/2000) Double Type (SQ1000/2000) Negative common spec.
Mount the switch in a location where there is no vibration (Display: greater than 98 m/s2, Sensor: 4.9 m/s2 or less), or no impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Table (1) Indication of Flow Characteristics Corresponding equipment Indication by international standard Other indications Standards conforming to ISO 6358: 1989 JIS B 8390: 2000 C, b Equipment for pneumatics JIS B 8390: 2000 Equipment: JIS B 8373, 8374, 8375, 8379, 8381 S Cv ANSI/(NFPA)T3.21.3: 1990 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-
Impact acceleration [m/s2] 5 0 50 100 150 200 250 300 Speed [mm/s] Relationship between speed and impact acceleration 120 in vacuum environments (1.3 x 104 Pa) low leakage, and low outgassing.