Cylinder with Lock When using the lock unit by placing it in parallel with the cylinder for driving as shown in the figure below, align the cylinder with the rod. Doing so may result in a decrease in holding force. Take additional safety measures when conducting equipment maintenance.
Series CDA2 models vary in the thickness of the cylinder tube wall.
In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
9 Note) In the case of cylinders with auto switches, rubber magnets are installed in the piston.
Please change the parameter in the initial setting. * For LECSS-T, please set the electronic gear with PC, PLC etc. in your application. 18 - 2.
MRQ D20The stopper ring is mounted on 120 clockwise from the standard position shown in Fig. 1-2 in Example 1, just as in Fig. 4-2 of Example 4. The stopper ring is mounted on 120 clockwise from the standard position shown in Fig. 1-2 in Example 1, just as in Fig. 3-2 of Example 3.
kg m 7.2330 ff Ib em 0.3937 in m 3.2810 fI Pressure mm(H,O) 000142 psi in 25.4 mm ft Ib 0.1383 kg m in 2.54 em II 0.3048 m Pressure in(H,O) 2.5357 x 10-3kg/em' Area in(Hg) 0.03518 kg/cm2 Area mm(Hg) 00197 psi in2 645.16 mm' psi 6.897 kPa mm' 0.0016 in2 torr 0.0197 psi em' 0.1550 1n2 kPa 0145 psi in2 6.4516 em' psi 0.06897 bar fI' 0.0929 m' psi 0.0703 kg/cm2 m' 10.765 fI' bar 14.50 psi kgcm2
Brown [Red] When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state. Brown [Red] Because there is no current leakage, the load voltage will not increase when turned OFF.
OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN 804 550 1256 862 1963 1347 3116 2126 5024 3434 7850 5388 1256 1002 1963 1569 3116 2500 5024 4035 7850 6260 32 18 CHQ 40 22.4 CHK B-series rod C-series rod 50 28 CHN 63 35.5 CHM 80 45 CHS 100 56 CH2 CH2 40 18 CHA 50 22.4 Related Products 63 28 D80 35.5 100 45 Water Resistant Hydraulic Cylinder R CHD2F F5BAL Mounting Bore
(Value in the initial stage.) No malfunction occurred in a one-sweep test between 8.3 and 2,000 Hz.Test was performed at both energize and de-energized states to the axis and right angle direction of the main valve and armature.(Value in the initial stage.)
in inch sizes are also available.
in head side RQ With boss in head side Note 1) In the case of without auto switch, M5 x 0.8 is used for 5 stroke only.
When using signal of the servo on (SON) by the I/O signal (CN6) . 0100 4 in HEX 0 0 in HEX 1100 C in HEX 0 0 in HEX When using signal of the Automatic/manual selection (MD0) by the I/O signal (CN6) 0001 1 in HEX 0 0 in HEX 1000 8 in HEX -49- * Enabling Servo-on (SON) and Automatic/manual selection (MD0) Signals Set PD12 to 0C04 and PD14 to 0801 in the I/O setting tab.
When using signal of the servo on (SON) by the I/O signal (CN6) . 0100 4 in HEX 0 0 in HEX 1100 C in HEX 0 0 in HEX When using signal of the Automatic/manual selection (MD0) by the I/O signal (CN6) 0001 1 in HEX 0 0 in HEX 1000 8 in HEX -44- * Enabling Servo-on (SON) and Automatic/manual selection (MD0) Signals Set PD12 to 0C04 and PD14 to 0801 in the I/O setting tab.
Loose or mechanical play in fixed parts or fixing screws.
Set "0" in the auxiliary function to make the dwell invalid. Set "1" in the auxiliary function and 0 in the dwell to perform varied speed operation.
Non-locking push type Push in the direction the arrow indicates. Connector Lead wire Valve body Pilot valve Locking slotted type Socket Press it to enable manual operation and turn it in the direction of the arrow to lock it. If this is not turned, it can be used in the same way as the non-locking type. Hook Surge Voltage Suppressor Simply turn in the direction of the arrow.
In the case of built-in magnet without auto switch, the symbol for auto switch is Nil.