The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable, Cyl, Slide Table, GUIDED CYLINDER, D79, 1056 lb
The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable, Cylinder, Slide Table, with Auto Switch, GUIDED CYLINDER, D83, 1056 lb
The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable, Cylinder, Slide Table, with Auto Switch, GUIDED CYLINDER, D83, 1056 lb
The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable GUIDED CYLINDER. Cylinder, Slide Table, with Auto Switch. 1056 lb. D83.
The bearing is a recirculating linear guide in a stainless steel housing. Air slide table w/built-in guide rail, Bore size *: 6, 8, 12, 16, 20, 25, Standard or symetric styles, Adjuster options: rubber stopper, shock absorber, metal stopper, Auto switch capable, Cylinder, Slide Table, with Auto Switch, GUIDED CYLINDER, D83, 1056 lb
MXW Series Long Stroke Slide Table Out: Cylinder extend In: Cylinder retract In Out Theoretical Output Table The dual rod ensures an output twice that of standard cylinders.
Solenoid valve Enter an "X" in the sections for valves to be used. In case of mixed port sizes, indicate by entering C4, L6, etc. In case of a manifold with external pilot specifications, enter an "X" in valve locations where an external pilot is required. Mixed internal and external specifications are also possible in this section.
If an excessive force is applied on the connector in the LOCK position, the connector block may be damaged. Also, using in such a way that the connector floats in the FREE position, it may cause the lead wire, etc. to break. Thus, refrain from using in these ways.
In such a case, use external pilot type. (When throttling IN port, or operating with OUT port open to the atmosphere or in a similar operation.)
INFORMATION Electric Actuator/Slider Type Motor Parallel Type RoHS Reduced in overall length Reduced in height Reduced dimension Parallel Parallel In-line Reduced dimension In-line Size Length reduction (mm) Motor mounting position (mm) Parallel In-line 16 80.5 416.5 497 25 75 460.5 535.5 32 87 495 582 40 102.6 553.4 656 Size Length reduction (mm) Motor mounting position (mm) Parallel In-line
case of Locking type, turn after pushing in.
Note 2) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed in both energized and de-energized states in the axial direction and at right angles to the main valve and armature.
conditions that exceed the lines in the graphs above, be sure to use a regenerative absorption unit.
Tightening the screws with a higher torque than recommended may result in a malfunction and/or decrease in guide accuracy, while tightening with a lower torque can result in the displacement of the mounting position or, in extreme conditions, the actuator could become detached from its mounting position.
In the case of large bore cylinder, even when the lock is released, operational resistance as shown in the table below is generated in a non-load state. CLQ MLGP RLQ Maintenance Caution MLU 1.
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the
In case of exceeding the following strokes, the cylinder is in the scope of the second class pressure vessel.
SYJ series valves can be configured on base mounted manifolds, or individually on sub-plates, creating a variety of solutions to meet your broadest engineering needs., SS3YJ7 manifold, 4/5 PORT SOLENOID VALVE, VVD, 1056 lb