VQC Do not operate multiple cylinders in synchronization. Avoid applications in which two or more cylinders with end lock are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 6. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control. 7.
Decide when to replace the pads, referring to the signs of deterioration, such as changes in the appearance due to wear, reduction in the vacuum pressure or delay in the transport cycle time.
the specification sheet in the case of CM and LM.
Cylinder side pressure (P2) IN IN Specifications Max. operating pressure Min. operatingpressure Ambient and fluid temp.
case of CP port plug is inserted in all 2(A) port.
Do not use in the atmosphere and environment over the rated specifications. 2. Do not use in the environment of corrosive gas or liquid splash. 3. Do not use in an environment where oil and chemicals are used. Maintenance Caution 1. Perform periodic inspection. 249
Make measurement on dimensions A as shown in Fig. 5 (b) and adjust it in such a way that Dimensions A are equal to those B, resulting in being at such a condition as shown in (e) of Fig. 5. As can be seen in Fig. 5 (a) and (b), the lock nut should be set to the bottom in the installation employing the joint. In the installation not employing the joint, set it to the top.
(If the devices are connected in series in the vacuum line, their conductances must be combined.)
When using the lock unit by placing it in parallel with the cylinder for driving as shown in the figure below, align the cylinder with the rod. Doing so may result in a decrease in holding force. Take additional safety measures when conducting equipment maintenance.
Series CDA2 models vary in the thickness of the cylinder tube wall.
In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
9 Note) In the case of cylinders with auto switches, rubber magnets are installed in the piston.
Please change the parameter in the initial setting. * For LECSS-T, please set the electronic gear with PC, PLC etc. in your application. 18 - 2.
MRQ D20The stopper ring is mounted on 120 clockwise from the standard position shown in Fig. 1-2 in Example 1, just as in Fig. 4-2 of Example 4. The stopper ring is mounted on 120 clockwise from the standard position shown in Fig. 1-2 in Example 1, just as in Fig. 3-2 of Example 3.
kg m 7.2330 ff Ib em 0.3937 in m 3.2810 fI Pressure mm(H,O) 000142 psi in 25.4 mm ft Ib 0.1383 kg m in 2.54 em II 0.3048 m Pressure in(H,O) 2.5357 x 10-3kg/em' Area in(Hg) 0.03518 kg/cm2 Area mm(Hg) 00197 psi in2 645.16 mm' psi 6.897 kPa mm' 0.0016 in2 torr 0.0197 psi em' 0.1550 1n2 kPa 0145 psi in2 6.4516 em' psi 0.06897 bar fI' 0.0929 m' psi 0.0703 kg/cm2 m' 10.765 fI' bar 14.50 psi kgcm2
Brown [Red] When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state. Brown [Red] Because there is no current leakage, the load voltage will not increase when turned OFF.
OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN 804 550 1256 862 1963 1347 3116 2126 5024 3434 7850 5388 1256 1002 1963 1569 3116 2500 5024 4035 7850 6260 32 18 CHQ 40 22.4 CHK B-series rod C-series rod 50 28 CHN 63 35.5 CHM 80 45 CHS 100 56 CH2 CH2 40 18 CHA 50 22.4 Related Products 63 28 D80 35.5 100 45 Water Resistant Hydraulic Cylinder R CHD2F F5BAL Mounting Bore
(Value in the initial stage.) No malfunction occurred in a one-sweep test between 8.3 and 2,000 Hz.Test was performed at both energize and de-energized states to the axis and right angle direction of the main valve and armature.(Value in the initial stage.)