Air Slide Table If an intermediate stop is performed by an external stopper, be careful of ejection when restarting. If lurching occurs, damage can result. If a slide table is stopped at an intermediate position by an external stopper and then moved forwards, after the slide table is returned to the back to retract the stopper, supply pressure to the opposite port to operate the slide table. 3.
) 46 (46) 10 to 100 117 (127) 127 (127) 107 (127) 10 43.5 (53.5) 53.5 (53.5) 140 (150) 150 (150) 130 (150) 12 53 (63) 63 (63) Note 1) ( ): Denotes the dimensions with auto switch.
After tightening by hand, the barb fitting type should be tightened by an additional 1/4 rotation using an appropriate wrench. 2. After tightening by hand, the barb elbow type should be tightened by an additional 1/2 rotation using an appropriate wrench. 2) M5 1. After tightening by hand, the barb fitting type should be tightened by an additional 1/6 rotation using a suitable tool. 2.
Refer to p.0-39 to 0-46 for Safety Instructions and common precautions. Snap Ring Installation/Removal q For installation and removal, use an appropriate pair of pliers (tool for installing a C snap ring).
NT-12 125, 140 M30 x 1.5 18 46 53.1 44 NT-16 M36 x 1.5 21 55 63.5 53 160, 180, 200 7-6-118 119 Series CQ2W Compact Cylinder: Large Bore Size Type Double Acting, Double Rod Dimensions: 125, 140, 160 The dimensions are the same with or without an auto switch.
When setting an auto switch, confirm the operation and adjust its mounting position.
How to Order Type 46 (5 port / Base mounted) Applicable solenoid valve 10-SYJ34310--SS5YJ3-46-05 -M5 Type 46 Type S46 Applicable blanking plate assembly SYJ3000-21-2A ( ) Single solenoid coil is located on the same side of A and B ports.
C95 Port location on head cover Perpendicular to axis Axial foot style Rail mounting style Symbol CP95 Nil R NCM If a built-in magnet cylinder without an auto switch is required, refer to the model of built-in magnet cylinder. For configuration, refer to page 6-3-46. Double clevis style is only available for being perpendicular to axis.
As the vacuum power of an ejector (venturi) rises, the vacuum flow actually lowers. When an ejector is used at its highest possible vacuum value, the vacuum flow will lower. Due to this, the amount of time needed to achieve adsorption is lengthened.
Because the retaining screws extend into the cylinder, this could lead to an air leak.
As the vacuum power of an ejector (venturi) rises, the vacuum flow actually lowers. When an ejector is used at its highest possible vacuum value, the vacuum flow will lower. Due to this, the amount of time needed to achieve adsorption is lengthened.
Never use in an atmosphere of explosive gases. The construction of the auto switch is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. The auto switch will malfunction or the magnets inside of an actuator will become demagnetized.
When the piston speed exceed 750 mm/s, make sure that direct impact does not apply on the cylinder cover by using an external stopper (shock absorber, etc). Standard external (B) 17 25 35 36 46 60 70 86 100 Dimensions except mentioned above are the same as standard type.
specification . 9-7 9.2 Outline dimensions . 9-8 9.2.1 HRS090-A-20/40/46-. 9-8 9.2.2 HRS090-W-20/40/46-. 9-9 9.3 Flow diagram . 9-10 9.3.1 HRS090-A-20/40/46-. 9-10 9.3.2 HRS090-W-20/40/46 . 9-10 9.4 Cooling capacity . 9-11 9.4.1 HRS090-A-20/40/46-. 9-11 HRS090 Series HRX-OM-T002 Contents 9.4.2 HRS090-W-20/40/46. 9-11 9.5 Pump capacity . 9-12 9.5.1 HRS090-A/W-20/40/46. 9-12 9.6 Types of hazard
If an external force over the allowable moment is applied, it may cause play in the guide or an increase in the sliding resistance. LEC SS-T LEC Y 6. Keep the flatness of mounting surface should be within 0.1 mm/500 mm.
Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized.
Operation stop Combination Symbol: D1 Combination Symbol: D4 An N.C. solenoid valve is used for the vacuum release valve. An external supply valve must be provided. An external valve must be provided to serve as the supply valve. An air operated N.C. valve is used for the vacuum release valve.
An external pilot style that can be used individually is available as a made-to-order. For details, refer to the page 4-6-46.
Note 4) When n is an odd number, an even number that is one larger than this odd number is used for the calculation. However, the minimum even number is 4. So, 4 is used for the calculation when n is 1 to 3.
The ABS data is also transmitted when an alarm is reset or when an emergency stop is reset. 2) An ABS checksum error is caused (Y3AON) if checksum inconsistency is found in transferred data. 3) The following time periods are measured.