Heatless Air Dryer ID Series Do not allow the weight of piping to lie directly on air dryer. 4. Do not connect a tube smaller than the port size to the inlet side. In particular, when using a resin tube, make sure that the size would not be smaller than the port size.
DO (n+1) Output interface Short circuit protection 0 V DO (n) FE / Shield Output circuit / Bus interface 24 V (logic / sensors) 0 V (logic / sensors) 24 V (valves / loads) 0 V (valves / loads) FE BUS . 8-3 EX245-DY1 60 No.EX-OMU0020CN 9.
Do not dispose this fluid in the environment.
-2No.PS-OMV0008CN-E / *3) 1 1.5 3) 1 1 () [] -3No.PS-OMV0008CN-E () () () () -4No.PS-OMV0008CN-E () * UL UL1310 2 UL1585 2 30 Vrms(42.4 V ) (2 ) UL (1 20 ) (ISE7G-T-ZS-48-A) N G -5No.PS-OMV0008CN-E Al2O3(96)C3604+FKM () O 1 /min 16MPa () * FG (35 N () ,() *() 6 33 -6No.PS-OMV0008CN-E () () 20 m DC(-)() * () () CE -5~70-5~50(5 ) (FKM) Al2O3()C3604()( ) -7No.PS-OMV0008CN-E
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
How to Order Do not replace heavy duty scrapers. XC4 Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. The CM2 series cannot replace either heavy duty scraper or rod seal. (It goes for replacing retainer assembly for the CS1 series.) Replace the CNA2 series with the lock unit.
F.O.F. 23N 2mm O.T. 3mm T.T. 3.5-32 VM800 Series VM800 Roller Lever/VM830-01-01 JIS Symbol 20 P.T. F.O.F. 20N 30 O.T. 50 T.T. Adjustable Roller Lever/VM830-01-13 JIS Symbol 20N F.O.F. At lever length 38.1mm 20 P.T. 30 O.T. 50 T.T. Adjustable Rod Lever/VM830-01-14 JIS Symbol 2.3N F.O.F.
Caution D: With connector DO: Without connector Y: With connector YO: Without connector When using the surge voltage suppressor type, residual voltage will remain. For details, refer to the Web Catalog (VP300/500 Low wattage specification). * Refer to the Web Catalog (VP300/500 Low wattage specification) for details of the DIN terminal. Assembly Example Products do not come assembled.
Note) Tighten within the tightening torque of 0.5 Nm 20%. Note: The orientation of a connector can be changed arbitrarily, depending on the combination of a housing (4) and a terminal block (3). 1.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Products compliant with IP65 and IP67 enclosures (Based on IEC529) are protected against dust and water, however, these products cannot be used in water. 3.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
N Nil Rc 3 1 0 14 to 60 l/min 20 to 1500 l/min 36 to 2600 l/min NPT Specifications Water/Non corrosive liquid Copper alloy Fluid Stainless steel 304 Liquid, which do not corrode stainless steel 304. Max. pressure 1 MPa 1.75 MPa Water resistance Insulation resistance 100 M (500 DC by megameter) 1500 VAC for one min.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
Do not to obstruct the aftercooler's vent inlet and outlet, and install the equipment more than 20 cm away from the walls or other equipment. 2. Install the aftercooler in a location that facilitates maintenance and inspection. 3. Install the aftercooler in a location with minimal vibrations. 4.
Note) When using the D-M9A(V), do not use the steel set screws which are included with the auto switch mounting brackets above (BMB10-032, BMB5-032, BA7-040, BA7-063).
FEP , PFA, Nylon, Soft nylon, Polyurethane 5 32 1 4 5 16 3 8 ", ", ", " Specification Fluid Air 100 kPa to 1 MPa 3 MPa 5 to 60C (No freezing) ANSI/ASMEB1. 20. 1 (NPT thread) JIS B 0212 (UNF thread) Operating pressure range 1) Proof pressure Ambient and fluid temperature Thread Note 1) Do not use the fittings with a leak tester or for vacuum retention because they are not guaranteed for zero
As the connected actuator will start operating due to this manual operation, be sure to confirm that it is safe to do so beforehand. Ex. 1) Cable length: 300 mm DXT1215T-5W1U-01m(-X1) Symbol for electrical entry MNon-locking push type Push the manual override button all the way down. 2.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
The VQ20/30's long life, high speed coil (up to 20 million cycles at 100cps for pneumatic use) along with its all plastic construction, make it an excellent choice for those who want high performance at a lower cost.Manifold for VQ20/30 pilot operated valve, Maximum 20 stations available as standard, Compact and lightweight, Optional DIN rail mount (equivalent to IP65), MFLD, 2-STA., 2