IDX-OM-W025 Length of the power cable The length of the power cable should extend less than 30m from the product. Connecting to the power supply Connect the power cable and the earth to the terminal block. M3 screw is used for the connection part. Make sure to use round crimped terminal. Applicable crimped terminal: 1.25-3 (Width: 6.5mm and below) Wiring procedure Remove the front panel.
Length of the power cable The length of the power cable and signal cable should extend less than 30m from the product.. Connecting to the power supply Connect the power cable and signal cable to the terminal block. M3 screw is used for the connection part. Make sure to use round crimped terminal.
IDFB Series 2-2Installation 2 4 IDX-OM-W019 Air Dryer 2 Transportation / Installation Length of the power cable The maximum length of the power cable should be no more than 98feet (30m).
If this product is connected using power cables that are more than 30m long or go outside of a building then external protection devices should be added to protect against electrical surge damage.
(The switch will stay ON all the time.) 1) Use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life.
(The switch will stay ON all the time.) 1) Use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life.
Length of the power cable The length of the power cable should extend less than 30m from the product.. Connecting to the power supply Connect the power cable and the earth to the terminal block. M3 screw is used for the connection part. Make sure to use round crimped terminal.
(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced.
(They may stay on continuously.) 2 Furthermore, even in the case of a type having a built-in contact protection circuit (D-B54, B64, D-B59W), if the length of the wiring to the load is extremely long (30m or more) and a PLC having a large rush current is used, confirm with SMC whether a contact protection box may be necessary.
D x 30M-36-CV (Cover: Made by HIROSE ELECTRIC CO., LTD.) Other interchangeable commercial cables with connectors can be also used. Pressure welding tools are required to connect the connector (plug, cover) models listed above and cables (order separately). The following products, including pre-assembled connectors and cables, are also available.
(The switch will stay ON all the time). 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced.
Length of the power cable The maximum length of the power cable should be no more than 98ft (30m). Connecting to the power supply Connect the power cable and the ground to the terminal block. Make sure to use the ring terminals for M3 screws. Applicable crimped terminal: 1.25-3 (Width: 6.5mm and below) Wiring procedure Remove the terminal block cover or the rear panel.
IDFB Series 2-2Installation 2 4 IDX-OM-W034 Air Dryer 2 Transportation / Installation Length of the power cable The maximum length of the power cable should be no more than 98feet (30m). Connecting to the power supply Connect the power cable and the ground to the terminal block. Wiring procedure 1. Remove the terminal block cover or the front panel. 2.
(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the inrush current and its life may be reduced.
(The switch will stay ON all the time.) 1) Use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life.
(The switch will stay ON all the time.) 1) Use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life.
USB (MR Configurator MTLEC-MR-SETUP221) 11 18 11 (b) USB LEC-MR-J3USB () USB MR-J3USBCBL3M () USB USB CN5 11.4 LEC-MR-J3BAT 45 (1) LEC-MR-J3BAT 12.4 (2) LEC-MR-J3BAT LEC-MR-J3BAT 19X(10)Y(11)Z(12) 200410SERIAL 4X 11 19 11 11.5 SSCNET11.1.5 UVW600VEP (2PNCT) 10 UL/cUL12 30m (1) L1 U U L2 V V L3 () W W L11 L21 P1 B1 P2 B2 N C P C P BU BV BW OHS1 OHS2 .
Length of the power cable The length of the power cable should extend less than 30m from the product. Connecting to the power supply Connect the power cable and the earth to the terminal block. M3 screw is used for the connection part. Make sure to use round crimped terminal. Applicable crimped terminal: 1.25-3 (Width: 6.5mm and below) Wiring procedure Remove the front panel.
(The switch will stay ON all the time.) 1) Use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced. It is again necessary to connect a contact protection box in order to extend its life.
(The switch will stay ON all the time). 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 2) Even if an auto switch has a built-in contact protection circuit, when the wiring is more than 30m long, it is not able to adequately absorb the rush current and its life may be reduced.