LEF-OM002xx (Only "With motor cover") (Nm) M2.5 0.3610% M3 0.6310% M4 1.510% M5 310% The fingernail of "Grommet" is inserted in the hole of "Pulley box". Grommet 43 - 7. Troubleshooting Alarms below are abstract of representative examples. For other alarms, see operation manual of controller. No.
MOT3 (6 ) 17 ENC4 (16 ) 4 18 MOT4 (6 ) ) (+)3 (+) 3 (+)4 (+)4 (+) 19 CI 3 4 ) 3 4 (+)(-) 20 M PWR 3 4 )5. 26 No.SFOD-OMT0009CN-B 4.3 (1) 5.5 (2) DIN 27 No.SFOD-OMT0009CN-B 4.4 (1) DIN (a) (4 M5 ) (M5)X4 (b) DIN DIN DIN (M5X8) DIN 2 4 3.0[Nm] M5X8 DIN 1 2 2 3.0[Nm] DIN M5X14 A DIN B DIN DIN (M5X14) 0.40.6 [Nm] 0.40.6[Nm] 28 No.SFOD-OMT0009CN-B A B M5X14 (2) M3
-38No.JXC-OMT0001CN-C (3) : CI C24V (+) (+) EMG1/EMG3 (+) 1 3 (+) (24V ) EMG2/EMG4 (+) 2 4 (+) (24V ) C24V EMG1/EMG3 EMG2/EMG4 LKRLS1/LKRLS3 LKRLS2/LKRLS4 LKRLS1/LKRLS3 + 1 3 (+) LKRLS2/LKRLS4 + 2 4 (+) PHOENIX CONTACT ( FK-MC0,5/5-ST-2,5) 2) AWG20(0.5mm oC 60 2.0 8mm -39No.JXC-OMT0001CN-C 6.2 (1)(3) C PWRCI M PWR (1) +24V 24-0V 24V 0V (24-0V) (24V) (0V) (+24V) M24V 0V 24V 0V M3
Loosen the hexagon socket head cap screws (M3 x 30:2 locations) which are fixing the SI unit. 2. Separate the SI unit to valve manifold. 3. Add and increase the attached tie-rod (2 pcs. per block) to the increased block respectively and pass through a block by the tie-rod. 4.
Caution (1)For M3, M5, 10-32UNF Tightening method (10)Do not apply excessive force or shock to For M3 First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a hexagon wrench. Refer to Table below for reference. the body or fittings with an impact tool.
The terminal screw is an M3 cross head screw. Note: Connect the ground terminal to ground. Resistance to ground should be 100 ohms or less. A. Single power supply used B.
Insulation resistance 1000 M Withstand voltage 1000 V Operating temperature range -30 to +55 oC VCTF 2 core cable (0.75 mm2 x 2) VCTF 4 core cable (0.75 mm2 x 4) Use the M3 crimped terminal for the connection.
The terminal screw is an M3 round head combination screw. Terminal Connection BS+ Connect the communication power supply BS+. BDH Connect the communication cable BDH. BDL Connect the communication cable BDL. BSConnect the communication power supply BS-.
B RATE Terminal board Terminal Connected to MS+ BS+ of communication power line BDH BDH of communication line BDL BDL of communication line BSBSof communication power line FG Ground line 24V 24V of solenoid valve power line 0V 0V of solenoid valve power line M3 terminal screw in use. EX##-OMF0012 8 EX##-OMF0012-A No.EX-OMF0012-B -9- 5-3. Address setting (1) ADDRESS NO.
Tighten the wiring screws (M3 slotted head screws) firmly with a tightening torque of 0.5 to 0.6 Nm. Make sure to connect "terminal resistor" between "CAN_H"-"CAN_L" to the units at the both ends of the system. Terminating resistor is 121 1%, 1/4 W (Refer to Fig. 2). Refer to Fig. 3 about how to connect to the unit.
Tighten the wiring screws (M3 slotted head screws) firmly with a tightening torque of 0.5 to 0.6 Nm. Be sure to connect a "Terminating resistor" to both ends of transmission line. (Refer to Fig. 2). Tighten the connector fixing screws (M2.5 slotted head screws) firmly with a tightening torque of 0.2 to 0.3 Nm.
Step 7 Reassembly of bonnet assembly (No.2) 3 Bolt 1 2 4 Bonnet assembly Port 1(P) Bolt size, Tool, Tightening torque of bolt (Nm) valve Bolt size Hex Tightening torque size wrench XLAV-16 M3 3 0.7 -25 M5 4 1.5 -40 M6 5 2.5 -50 M8 6 6.1 Body -63 M10 8 15 -80 Turn ON the solenoid valve to supply air pressure of 0.4MPa (G) to the port 1(P).
Air flow adjustment switch Scale Air flow [m3/min] 1 0.19 2 0.46 3 0.66 4 0.80 4-4. Maintenance Warning Function and Cleaning If the product is used for an extended period with dust present on the emitters, the product performance will be reduced.
Tightening torque (1) Round head combination screw (M2.5 x 41): 0.3 to 0.36 Nm (4) Hexagon socket head cap screw (M3 x 30): 0.6 to 0.66 Nm Replacement procedure of ZL212-SP01 (Silencer set) Disassembly and Reassembly 1. Remove the four round head combination screws (M2.5 x 53) (1). 2.
Applied voltage When connecting fittings to valves, tighten as indicated below. 1) M3, M5 types 1. When using SMC fitting, follow the guidelines below. After tightening by hand, tighten an additional 1/4 (M3), 1/6 (M5) turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand.
from above / through hole type Screw material SUS Screw dimensions M2.5 x 0.45 Recommended tightening torque [Nm] 0.27 to 0.36 L3 (Maximum screw-in depth) [mm] 2.5 L4 (Plate thickness) [mm] 2.1 3 Work piece mounting / top mounting type Screw material SUS Screw dimensions M3 x 0.5 Recommended tightening torque [Nm] 0.48 to 0.63 L5 (Maximum screw-in depth) [mm] 2.5 (5) When connecting the
SYJ7000 M3 0.8Nm Caution Replacement of Pilot Valve Pilot valve in this series are improved to provide excellent energy saving results. However following this improvement, these new valves are no longer compatible with the conventional pilot valve used at the interface.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side Note2 When compressor oil mist discharge concentration is 30mg/m3 (ANR). Note3 Bowl seal and other O-rings are slightly lubricated.
Class B coil: AWG20 Insulator O.D. 2.5 mm Terminal cover Round head combination screw M3 Tightening torque: 0.5 to 0.6 Nm mark mark Tightening torque: 0.5 to 0.6Nm Round head combination screw M3 Tightening torque: 0.5 to 0.6Nm Conduit terminal Cross section A-A (Wiring inside) Lead wire Seal Conduit piping (Port size G1/2 Tightening torque 0.5 to 0.6Nm) Rated voltage Lead wire color (1)
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side Note 4 When the compressor oil mist discharge concentration is 30 mg/m3 (ANR). Note 5Bowl seal and other O-rings are slightly lubricated.