Air Gripper for collaborative robots. Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. 2. Do not use in direct sunlight. 3. Do not operate in a location subject to vibration or impact. 4. Do not mount the product in locations where it is exposed to radiant heat. 5.
Note) Do not change the rated voltage.
Recommended tightening torque Unit: N m Thread size 18 14 38 12 34 1 1 1/4 1 1/2 Torque 7 to 9 12 to 14 22 to 24 28 to 30 28 to 30 36 to 38 40 to 42 48 to 50 (4) Do not apply a spanner to the pressure switch body during piping. Otherwise, the product may be damaged. (5) Do not apply torsion or bending moment other than the weight of the product itself.
, 125, 150 200, 250, 300 MGT 125 107 19 16 160 176 110 125 9 12 85 165 M8 37 160 40 70 95 60 38 150 142 25 19 190 210 115 135 11 12 95 200 M10 42 194 45 82.5 115 75 50 Bore size (mm) P Note 2) Q R S T U V W WH X Y Z O 20 25 32 40 50 86 80 M6 x 1 M5 x 0.8 21 12 26 12 40 36 30 140 23 M6 x 1 M5 x 0.8 21 12 31 13 98 47 44 37 80 153 25 M6 x 1 1/8 21 12 38 16 112 53 50 37 82 161 28.5 M8 x 1.25
V 24 V Connector Grommet Diagnostic indication (2-color display) 3-wire (NPN) 3-wire (PNP) IC circuit 5 V, 12 V Grommet 2-wire 12 V Solid state switch Connector Relay PLC 3-wire (NPN) 3-wire (PNP) 5 V, 12 V 24 V IC circuit Diagnostic indication (2-color display) Grommet 12 V 5 V, 12 V 2-wire Water resistant (2-color display) 4-wire (NPN) IC circuit With diagnostic output (2-color
a2 = m 12 a2 = m1 +m2 3 a12 3 a22 12 4a12 + b2 = m1 CRBU2 12 4a22 + b2 + m2 CRB1 7.
12 12 13 20 25 32 40 190 205.5 208.5 235 149 159 162 178 12 12 12 13 125 135 136 151 186 201 204 230 149 159 162 178 12 12 12 13 14 14 14 15 201 to 350 301 to 400 301 to 450 301 to 800 11 11 11 12 20 25 32 40 9-2-32 Series CLG1 Fine Lock Cylinder Double Acting, Single Rod Construction With rubber bumper: CLG1BN CL CL1 MLGC CNG MNB With air cushion: CLG1BA CNA CNS CLS CLQ MLGP RLQ Component
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Adjusting screw width across flats Lock nut A tightening torque Model 12-REA25 12-REA32 12-REA40 12-REA50 12-REA63 Width across flats (mm) 5 5 6 8 8 Model 12-REA25 12-REA32 12-REA40 12-REA50 12-REA63 Tightening torque (Nm) 1.2 1.2 2.1 3.4 3.4 5. Do not scratch or gouge the external surface of the cylinder.
LEKFS25(L/R)/Ball Screw Drive Horizontal Vertical 20 30 Lead 6: LEKFS25(L/R)EB Lead 6: LEKFS25(L/R)EB 25 15 Work load: W [kg] Work load: W [kg] 20 Lead 12: LEKFS25(L/R)EA 10 15 Lead 12: LEKFS25(L/R)EA 10 Lead 20: LEKFS25(L/R)EH 5 Lead 20: LEKFS25(L/R)EH 5 0 0 0 100 200 300 400 500 600 0 200 400 600 800 1000 1200 Speed: V [mm/s] Speed: V [mm/s] LEKFS32(L/R)/Ball Screw Drive Horizontal Vertical
wiring diagram Analog output, voltage type Brown Blue White Breathing hole M3 x 0.5 Monitor output voltage Black 2 14-8-11 12 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 14-8-12 13 Electro-pneumatic Regulator Series ITV1000/2000/3000 F.R.L.
OUT1 12 to 24 VDC 12 to 24 VDC Load Load Load White OUT2 White OUT2 Load Blue DC () Blue DC () -R: NPN (2 outputs) + Auto-shift input -S: NPN (2 outputs) + Auto-shift input -T: PNP (2 outputs) + Auto-shift input -V: PNP (2 outputs) + Auto-shift input Brown DC (+) Brown DC (+) Load Gray Auto-shift input Gray Auto-shift input Load + + Black OUT1 Black OUT1 12 to 24 VDC 12 to 24 VDC Load
Joint 7 9 YB-03 32, 40 11.5 depth 7.5 34 25 12 K ( across flats) H (With locking) 9 11 YB-05 50, 63 42 32 12 14.5 depth 8.5 11 13 YB-08 80 52 38 16 18 depth 12 d2 d1 14 17 YB-10 100 62 50 19 21 depth 14 L UT C UA Bore size (mm) T1 RS Weight (g) T2 V W Part no. Part no.
Do not grip the piping port on the back side or the handles of the panel. 3. Do not pass over bumps etc. with the casters.
V 12 V Relay, PLC Yes Yes Grommet 24 V IC circuit 5 V,12 V Diagnostic indication (2-color indication) 12 V IC circuit A96V A96 5 V 12 V Grommet A93V A90V A93 A90 100 V Relay, PLC 2-wire 24 V IC circuit 100 V or less No Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ Solid state auto switches marked with are
If they do not match, stress could be applied to the rod and the cylinder tube, causing wear to the inner surface of the cylinder tube, the bushing, the rod surface, and the seals may become damaged. 3) When mounting the cylinder, do not apply a lateral load to the rod.