EXxx-OMC0002 The terminal screw is an M3 round head combination screw. Terminal Connection BS+ Connect the communication power supply BS+. BDH Connect the communication cable BDH. BDL Connect the communication cable BDL. BSConnect the communication power supply BS-.
B RATE Terminal board Terminal Connected to MS+ BS+ of communication power line BDH BDH of communication line BDL BDL of communication line BSBSof communication power line FG Ground line 24V 24V of solenoid valve power line 0V 0V of solenoid valve power line M3 terminal screw in use. EX##-OMF0012 8 EX##-OMF0012-A No.EX-OMF0012-B -9- 5-3. Address setting (1) ADDRESS NO.
Tighten the wiring screws (M3 slotted head screws) firmly with a tightening torque of 0.5 to 0.6 Nm. Make sure to connect "terminal resistor" between "CAN_H"-"CAN_L" to the units at the both ends of the system. Terminating resistor is 121 1%, 1/4 W (Refer to Fig. 2). Refer to Fig. 3 about how to connect to the unit.
Tighten the wiring screws (M3 slotted head screws) firmly with a tightening torque of 0.5 to 0.6 Nm. Be sure to connect a "Terminating resistor" to both ends of transmission line. (Refer to Fig. 2). Tighten the connector fixing screws (M2.5 slotted head screws) firmly with a tightening torque of 0.2 to 0.3 Nm.
Step 7 Reassembly of bonnet assembly (No.2) 3 Bolt 1 2 4 Bonnet assembly Port 1(P) Bolt size, Tool, Tightening torque of bolt (Nm) valve Bolt size Hex Tightening torque size wrench XLAV-16 M3 3 0.7 -25 M5 4 1.5 -40 M6 5 2.5 -50 M8 6 6.1 Body -63 M10 8 15 -80 Turn ON the solenoid valve to supply air pressure of 0.4MPa (G) to the port 1(P).
Air flow adjustment switch Scale Air flow [m3/min] 1 0.19 2 0.46 3 0.66 4 0.80 4-4. Maintenance Warning Function and Cleaning If the product is used for an extended period with dust present on the emitters, the product performance will be reduced.
Tightening torque (1) Round head combination screw (M2.5 x 41): 0.3 to 0.36 Nm (4) Hexagon socket head cap screw (M3 x 30): 0.6 to 0.66 Nm Replacement procedure of ZL212-SP01 (Silencer set) Disassembly and Reassembly 1. Remove the four round head combination screws (M2.5 x 53) (1). 2.
Applied voltage When connecting fittings to valves, tighten as indicated below. 1) M3, M5 types 1. When using SMC fitting, follow the guidelines below. After tightening by hand, tighten an additional 1/4 (M3), 1/6 (M5) turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand.
from above / through hole type Screw material SUS Screw dimensions M2.5 x 0.45 Recommended tightening torque [Nm] 0.27 to 0.36 L3 (Maximum screw-in depth) [mm] 2.5 L4 (Plate thickness) [mm] 2.1 3 Work piece mounting / top mounting type Screw material SUS Screw dimensions M3 x 0.5 Recommended tightening torque [Nm] 0.48 to 0.63 L5 (Maximum screw-in depth) [mm] 2.5 (5) When connecting the
SYJ7000 M3 0.8Nm Caution Replacement of Pilot Valve Pilot valve in this series are improved to provide excellent energy saving results. However following this improvement, these new valves are no longer compatible with the conventional pilot valve used at the interface.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side Note2 When compressor oil mist discharge concentration is 30mg/m3 (ANR). Note3 Bowl seal and other O-rings are slightly lubricated.
Class B coil: AWG20 Insulator O.D. 2.5 mm Terminal cover Round head combination screw M3 Tightening torque: 0.5 to 0.6 Nm mark mark Tightening torque: 0.5 to 0.6Nm Round head combination screw M3 Tightening torque: 0.5 to 0.6Nm Conduit terminal Cross section A-A (Wiring inside) Lead wire Seal Conduit piping (Port size G1/2 Tightening torque 0.5 to 0.6Nm) Rated voltage Lead wire color (1)
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side Note 4 When the compressor oil mist discharge concentration is 30 mg/m3 (ANR). Note 5Bowl seal and other O-rings are slightly lubricated.
Manually unlocking For 20 to 32 Dust cover holding bolt Dust cover Manual unlocking bolt Manual unlocking bolt Lock ring Locking direction Locking direction Lock ring Rod side Head side Rod side Head side MLGP--F: Extension locking MLGP--B: Retraction locking 1) Remove the dust cover. 2) Screw a manual unlocking bolt (a bolt of M3 x 0.5 x 15L of more commercially available) into the lock
See Fig. 4] For FN112-10, two screws are mounted in the middle of the guide assembly [M3 See Fig. 4] 2-6. The element can now be pulled out of the cover. Do not disassemble the element any further. Note) Reassembly should be performed by reversing the disassembly procedure. Refer to the schematic drawings for the assembly and disassembly procedures for the cover, seals etc.
Standard Strokes Stroke (mm) Bore size (mm) Bore size (mm) Mounting bracket Applicable switch Note 50 100 75 125 150 175 200 250 300 400 500 25 Switch mounting screw (M3 X 0.5 X 8 l ) Square nut 12 V V V V V V D-A7, A8 D-A7lH, A80H D-A73C, A80C D-A79W D-F7lV D-F7, J7 D-J79C D-F7lWV D-F79W, J79W 12 20 BQ-1 20 V V V V V V V V 32 V V V V V V V V V Switch mounting screw (M3 X 0.5 X 10 l )
X 0.5 M10 X 1.0 9 18.5 25.5 32.5 3 27.5 34.5 41.5 3 10 19 22 6 14.5 21 28 12 12 3.5 M4 X 0.7 M15 X 1.5 13 20.5 27 34 4 32.5 39 46 5 12 27 31 7 16.5 22.5 29 19 14 4.2 M5 X 0.8 M22 X 1.5 20 23.5 29.5 36 5 37.5 43.5 50 6 Plug Mounting Style CJPS B C E G H K MM NN 5st 10st F 15st R 5st 10st S 15st W Q 5st 10st Z Bore (mm) 6 10 15 A 15st 7 12 13.9 6 12.5 19.5 26.5 8.5 9 3.5 M3 X 0.5 M10 X 1.0
Universal mounting Model Model Size (Nominal x Height) Piece Metric size Inch size TMH-23J TMH-04J TMH-06J TMH-06 TMH-01J TMH-03J TMH-05 TMH-07 TMH-09 TMH-11 TMH-13 M3 x 15 M3 x 20 1 M4 x 25 TMH-08 TMH-10 TMH-12 The holder can be used to secure an individual part.
A I 18 6 21 9 5 5 23 34 Side A Side B 12-11-13 14 Series MRHQ Dimensions MRHQ16 A B 41 50 66.5 4-M5 x 0.8 depth 8 30 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 0 -0.062 47h9 +2.2 -0.2 20.9 opened 0 -0.1 5 41 +0.03 0 3-4H9 depth 6 (one each on three sides) 4-M3
Tighten the screws (M3) for mounting the blank cover in the range of 0.3 0.03Nm. Failure to observe these torque values could lead to equipment damage.