ZSE30/ISE30 Note Lead wire length: 2m With mounting screws (M3 x 5L: 2 pcs.)
Combination screw M3 Tightening torque 0.5 to 0.6 Nm Combination screw M3 A Conduit terminal View A-A (Internal connection diagram) G + mark mark + 1 2 Series VC A Conduit When used as an IP65 equivalent, use seal (Part no. VCW20-156) to install the wiring conduit. Also, use the tightening torque below for the conduit.
N.C. 9 LVM20R4 11 11 2 depth 3 2 depth 3 5 5 2 x 5.7 3 x 5.7 6.8 6.8 6.8 LVM205R LVM20R3 Recommended interface dimensions Surface roughness = Rz3.2 or less Surface roughness = Rz3.2 or less 31 0.1 31 0.1 15.5 0.1 15.5 0.1 11 2 x M3 x 0.5 Effective thread length 4.5 or more 6.8 0.1 6.8 0.1 6.8 0.1 2 x M3 x 0.5 Effective thread length 4.5 or more 6.5 0.1 When using a positioning pin
The purity class of compressed air quality based on ISO8573-1:2010 2 : 6 : 3 Solid particle Moisture Oil Max number of particles per m3 Oil concentration (mg/m3) 0.1 < d 0.5 0.5 < d 1.0 1.0 < d 5.0 Pressure dew point Particle size d (m) Class Class Class (oC) at air pressure of 0.7 MPa 1 20,000 400 10 1 -70 1 0.01 2 400,000 6,000 100 2 -40 2 0.1 3 Not specified 90,000 1,000
The connection size is M3. Applicable crimped terminal width: 6.5mm or less [Wiring procedure] 1. Remove the front panel of the product. 2. Introduce the cable through the grommet with membrane to connect to the terminal block. (Refer to the label on the terminal block.) M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3.
The connection size is M3. Applicable crimped terminal width: 6.5mm or less [Wiring procedure] 1. Remove the front panel of the product. 2. Introduce the cable through the grommet with membrane to connect to the terminal block. (Refer to the label on the terminal block.) M3 tightening torque: 0.63 to 1Nm. Do not touch equipment other than the terminal block during wiring. 3.
BH BI (UU) 2-M3 x 0.5 (opposite side, same location) (For front port, use hexagon socket head set screw) Q H 2-J through JA depth of counter bore JB (opposite side, same location) 1.5 S BE CA CB BF DD D BD BG A 2.2 (0.4) Note 1) SD 16 BA 2-M3 x 0.5 depth 4 BB W 2-M3 x 0.5 (For side port, use hexagon socket head set screw) N BC Note 2) For the 180 specification, the slated line area do not
For Use in North, Central and South America Refrigerated Air Dryer (UL, CSA Standards) Applicable for the high-temperature environments Ambient temperature : Max. 113F (45C) Inlet air temperature : Max. 149F (65C) Air flow capacity * IDFB90-23, Dew point of 50F (10C) 459 SCFM (780 m3/h) (13% increase compared to the current model) Power supply voltage Single-phase 230 VAC (60 Hz) Single-phase
Specifications 40 Dimensions 40 -1No.EX-OMI0003-H Input Unit Summary of Product Parts 41 Mounting and Installation 42 Installation 42 Wiring 44 Specifications 48 Specifications 48 Dimensions 48 Maintenance 49 Troubleshooting 50 Option 55 -2No.EX-OMI0003-H Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com VT Type 42 Type S42 1 (P) 3 (R) (Valve leakage: 0.03 cm3/s He or less) Can be used in vacuum/release circuits VP VG Universal porting Type 40 VP N.C.
Air consumption (L/min [ANR]) SUP = 0.7 MPa 40 35 30 SUP = 0.5 MPa 25 20 SUP = 0.35 MPa Caution 15 SUP = 0.2 MPa 10 1.
Ltd. 89 Tuas Avenue 1, Jurong Singapore 639520 TEL: 6861-0888 FAX: 6861-1889 RUSSIA SMC Pneumatik LLC. 36/40 Sredny prospect V.O. St.
Mounting screw(M3) Tightening torgue 0.5 to 0.7Nm A DIN rail mount bracket fig. 3 When setting to DIN rail, place A of fig. 3 into DIN rail. While pushing it, fix it by the clamp of screw in fig. 4. Inadequate pushing may cause falling of parts.
drain Max. air flow capacity Note 1) 600 L/min(ANR) 120 L/min(ANR) 240 L/min(ANR) Filtration rating 0.01 m (99.9% filtered particle size) Outlet side oil mist concentration Max. 0.1 mg/m3(ANR) [before the saturation of oil: 0.01 mg/m3(ANR) or less0.008 ppm] Compressed air quality class Note 2) ISO8573-1:2010 [1:7:2] 45 cm3 Drain capacity 8 cm3 25 cm3 Bowl material Polycarbonate Bowl guard
Type 40 Easy manual operation Since manual overrides are located in 2 directions, on the top and on the side of the valve, manual override operation is possible unaffected by mounting space and piping direction, etc. Ozone resistant (Series 80-) FKM (fluororubber) is used for the fluidcontact rubber materials, allowing use even in ozone environments.
(Operation 60%, Holding 40%) Approx.4,000hrs. (Operation 60%, Holding 40%) motor does not start or operation stops suddenly. Travel km L[]Z[]5L 280 L[]Z[]3M 640 L[]Z[]5M 850 L[]Z[]3 200 1,700 L[]Z[]3H 1,200 Note. Refer to the shorter data shown above. Energizing tim e Reference of travel depending lead Horizontal direction Reference for energizing tim e Model no.
ISO compressed air quality class The class regarding the cleanliness of compressed air (solid particles, moisture and oil) stipulated by ISO 8573-1:1991 (JIS B8392-1:2000) Maximum oil concentration (mg/m3) Minimum pressure dew point (C) Maximum particle size (m) Quality class 1 2 3 4 5 6 0.01 0.1 1.0 5 25 70 40 20 3 7 10 0.1 1 5 15 40 Notation system Example) Solid particle size: 0.1 m
Specifications Compressed air 1.0MPa Fluid Max. operating pressure Min. operating pressure(1) 0.05MPa 1.5MPa Proof pressure Ambient and fluid temperature 5 to 60C Filtration 0.3m (95% particle size collection) Max.1.0mg/m3(ANR) (08ppm)(2) Oil mist removal rate 2 years or when pressure drop reaches 0.1MPa Element life Note 1) With Auto drain: 0.15MPa Note 2) At oil mist removal rate blowing
Wiring 22 Outline of Settings [Measurement mode] 24 Pressure Setting 25 3 Step Setting Mode 26 Simple Setting Mode 28 Function Selection Mode 30 Function selection mode 30 Default setting 30 F 0 Display units, switch output specifications and diagnostic information selection function 32 F 1 Setting of OUT1 34 F 2 Setting of OUT2 37 F 3 Digital filter setting 39 F 4 Auto-preset function 40
13 13 16 16 19 19 22 22 32 100 63 113 76 119 76 145 90 151 90 166 106 173 106 200 122 253 160 8 12 6 40 66 84 28 5 2.0 27 37 1/4,3/8 172 AMH250 178 1/2 8 12 6 40 66 84 28 5 2.0 27 37 3/8, 1/2 204 AMH350 3/4 210 8 14 7 50 80 100 34 5 2.3 32 37 8 14 7 50 80 100 34 5 2.3 32 37 10 14 9 55 88 110 50 9 3.2 37 37 10 14 9 55 88 110 50 9 3.2 37 37 10 16 9 65 102 130 60 10 4.5 39 37 15 20 11 85 136