IDX-OM-P026E Do not peel or rub off the hazard labels. Carefully confirm where the hazard labels are affixed. CAUTION !
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. UL approved product Caution 5. Do not use in a place subject to heavy vibration and/or shock. When conformity to UL is required, the SI unit should be used with a UL 1310 Class 2 power supply.
Use clean air Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gasses, etc., as it can cause damage or malfunction. Warning Screwing piping Reasonable tightening torque N m Rc1/8 7~ 9 Rc1/4 12~ 14 6.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
I-020B I-032B I-040B 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 18 41 M8 x 1.25 14 10 11 66 46 16 20 36 M8 x 1.25 10 14 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 22 45 14 10 14 69 48 18 20 38 10 14 M10 x 1.25 M10 x 1.25 0.070 0 0.1 0.3 0.070 0 0.1 0.3 12 16 12 16 24 50 20 14 13 92 69 22 24 55 20 M14 x 1.5 M14 x 1.5 15.5 Double Knuckle Joint Mounting Y (Max.) hole H10 Shaft (mm) H L MM ND NX2
I-020B I-032B I-040B 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 18 41 M8 x 1.25 14 10 11 66 46 16 20 36 M8 x 1.25 10 14 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 22 45 14 10 14 69 48 18 20 38 10 14 M10 x 1.25 M10 x 1.25 0.070 0 0.1 0.3 0.070 0 0.1 0.3 12 16 12 16 24 50 20 14 13 92 69 22 24 55 20 M14 x 1.5 M14 x 1.5 15.5 Double Knuckle Joint Mounting Y (Max.) hole H10 Shaft (mm) H L MM ND NX2
I-020B I-032B I-040B 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 18 41 M8 x 1.25 14 10 11 66 46 16 20 36 M8 x 1.25 10 14 0.058 0 0.1 0.2 0.058 0 0.1 0.2 9 9 9 9 22 45 14 10 14 69 48 18 20 38 10 14 M10 x 1.25 M10 x 1.25 0.070 0 0.1 0.3 0.070 0 0.1 0.3 12 16 12 16 24 50 20 14 13 92 69 22 24 55 20 M14 x 1.5 M14 x 1.5 15.5 Double Knuckle Joint Mounting Y (Max.) hole H10 Shaft (mm) H L MM ND NX2
58 M16 x 1.5 91 120.5 5.5 48 39 122 236 Note) Refer to pages 13 and 14 for accessories.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks. 4. Do not mount the product in locations where it is exposed to radiant heat.
Do not wire in conjunction with power lines or high voltage lines. Wire separately from power lines and high voltage lines, and avoiding wiring in the same conduit with these lines. Control circuits including switches may malfunction due to noise from these lines. 5. Do not allow a load to short circuit.
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling except for priming the pump. 5 11.
Connection thread Proper tightening torque (Nm) Rc, NPT, G, PNTF 1/4 12 to 14 Rc, NPT, G, PNTF 3/8 22 to 24 4. Air Supply Warning 1. Use clean air. Do not use compressed air that includes chemicals, synthetic oils containing organic solvents, salinities or corrosive gases, etc., as it can cause damage or malfunction. 2.
If you do not agree to the following disclaimer, you may not use or copy this software. "Disclaimer" 1.
(ML2B) (CE1-R) DO-ring Parts sorting: To classify the different types of parts.
Do not use the product where these are present.
(ML2B) (CE1-R) DO-ring Parts sorting: To classify the different types of parts.
When performing neutralization, do not input the ionizer stop signal.