ISE35.eng Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error name Error display Error type Troubleshooting method Turn the power off and remove the cause of the over current. Then turn the power on.
Zero clear error [oU1] Output mode (OUT1) [HYS] Hysteresis mode more than 20 mm Cover [1ot ] Reversed output (OUT1) [1_P] Normal output Caution [F 1] [P_1] Input of set value (OUT1) Medium value of rated flow range Insulator Reset the accumulated flow. (pressing and buttons simultaneously for 1 second or more) Do not touch the terminals and connectors while the power is on.
Function Setting Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Mounting screw Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not make any upward angles in drain line.
Do not hold the terminal block box or the switch. ISE70 ZSE80 ISE80 Lead wire with connector ZSE ISE Knurl ZSP PS 3. Connect the colored wires coming from the cable terminal. Refer to the circuit diagram and table above to avoid mistakes.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution IRV 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. VEX SRH Piping Warning SRP SRF 1.
Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution IR 1. For emergency action in the event of setting failure or leakage from the relief port, refer to Troubleshooting in the Operation Manual of the product. IRV VEX Piping Warning SRH SRP 1.
Design AT Caution Maintenance Caution IDl q Do not use this product in a line in which the pressure pulsation cycle is frequent. If it must be used under such conditions due to unavoidable circumstances, contact SMC beforehand. w Do not use it with anything other than dry air (such as air containing moisture).
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 3-12-6
20 20.5 25 30 34 12.8 19 23 23 M4 M5 M5 M5 1/4 1/4, 3/8 3/8, 1/2 3/4 VCA41 17-2-13 8 Series VCA How to Order Manifold (VCA20) How to Order Manifold Assembly VV2C A 2 02 02 Enter the mounting valve and option part numbers under the manifold base part number.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including change of printed circuit board) or repair. An injury or failure can result. 1 s. after This function is to display error location and content when a problem or an error occurs. All indications Instantaneous value indicatio Error Name Error Display Error Type Troubleshooting Method Do not operate outside of the specification.
Do not drop, dent, or allow excessive impact to cylinder during handling. 5, Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto 3. switch are mounted in parallel. up, although the auto switch will function. Do not exceed specified current or the LED might be damaged and not functjon.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not drop, dent, or allow excessive impact to cylinder during handling. 5, Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto 3. switch are mounted in parallel. up, although the auto switch will function. Do not exceed specified current or the LED might be damaged and not functjon.
kg] 0 10 20 30 40 50 60 Work load [kg] 1500 1500 1500 Mep 1000 1000 1000 L3 [mm] L3 [mm] L3 [mm] m L3 Z 500 500 500 0 0 0 0 10 20 30 40 50 60 Work load [kg] 0 5 10 15 20 Work load [kg] 0 10 20 30 40 Work load [kg] 1500 1500 1500 L4 1000 1000 1000 L4 [mm] L4 [mm] L4 [mm] X 500 500 500 0 0 0 0 5 10 15 20 Work load [kg] 0 10 20 30 40 Work load [kg] 0 10 20 30 40 50 60 Work load [kg] 1500 1500
Normal Bottom Peak BATTERY 1.5V x 2 LR6 G kV MADE IN JAPAN IZD IZE POWER LIGHT 110 Do not apply a strong impact on the sensing part.