SI Unit for Vacuum Manifold Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set up with wet hands. An electric shock can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Recommended Piping Conditions 9 - Warning (1)Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. (2)Do not expose the product to direct sunlight for an extended period of time. (3)Do not use in a place subject to heavy vibration and/or shock. (4)Do not mount the product in locations where it
21 24 33 37 47 55 8.5 8.5 10.5 10.5 11.5 12.5 10 10 12 12 14 15 6.6 6.6 9 9 11 11 38 41 50 52 66 76 18 22 30 35 40 50 31 35 45 50 60 70 15 18 20 23 27 30 51 54 65 67 86 96 32 36 45 50 63 71 32 40 50 63 80 100 10.5 12 15 15 18 18 14 16 21 21 25 25 Centre trunnion Bore (mm) TC B TA TF Part No.
(Blank plate ass'y) VZ VS Combinations of Solenoid Valve, Manifold Gasket and Manifold Base Blank Plate Assembly Body ported (SYJ7l2) Base mounted (SYJ7l4) SYJ700-10-2A Phillips head screw M3 X 8, Matt nickel plated Phillips head screw M3 X 31, Matt nickel plated Blank plate SYJ700-10-2 Gasket DXT201-14-3 Manifold gasket DXT201-14-2 Manifold gasket DXT201-14-1 Applicable base Sub-plate SS3YJ7
We do not guarantee against any damage if the product is used outside of the specifications range. (2) Do not disassemble the product or make any modifications, including additional machining.
Do not stack a lot of seals, or deform or damage seals by putting a heavy object on top of them. White particles can emerge from the surface of the seal during storage, but they do not affect its performance. 23 3-4. Troubleshooting Problem Major causes Countermeasures Operation has lost smoothness. 1.
Please do not tighten the needle forcibly. (3)Tighten threads with the proper tightening torque.
Refer to each construction drawing on the fittings and tubing material. (2) Do not expose the product to direct sunlight for an extended period of time. (3) Do not use in a place subject to heavy vibration and/or shock. (4) Do not mount the product in locations where it is exposed to radiant heat. (5) Do not use the ordinary fittings and tubing in locations where static electricity would
Input unit LED Refer to fault and the input data No. 14. do not match. -69No.EX-OMT0009 Troubleshooting Fault No. 1 Fault Possible cause Investigation method Countermeasures Tighten the power supply cable connection. (if there is a broken wire, replace the cable).
(Page 11) 6 - 2) Avoid having a large gap between the clevis or trunnion and mating bushing, as this exposes the pin to a bending load. 3) Do not let foreign matter such as cutting chips get into the product from the suction port. 4) Do not touch the cylinder during high speed and high frequency operation.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3. Do not service or attempt to remove product and machine 3.
Operating environment Warning (1)Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. (2)Do not expose the product to direct sunlight for an extended period of time. (3)Do not use in a place subject to heavy vibration and/or shock. (4)Do not mount the product in locations where it is exposed to
Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including switches, may malfunction due to noise from these other lines. 5. Do not allow short circuiting of loads.
Do not peel or rub off the hazard labels. Carefully confirm where the hazard labels are affixed. CAUTION !
Do not peel or rub off the hazard labels. Carefully confirm where the hazard labels are affixed. CAUTION !
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. UL approved product Caution 5. Do not use in a place subject to heavy vibration and/or shock. When conformity to UL is required, the SI unit should be used with a UL 1310 Class 2 power supply.
Use clean air Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gasses, etc., as it can cause damage or malfunction. Warning Screwing piping Reasonable tightening torque N m Rc1/8 7~ 9 Rc1/4 12~ 14 6.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.