Compact Vacuum Unit Ejector/ Vacuum Pump System M5 (PV, PD port): After tightening by hand, increase the tightening by about 1/6 turn with a tightening tool. Tightening torque is 1 to 1.5N as a guide. (3) When mounting or removing the tube fitting, etc. to the manifold base, hold the manifold base hold the manifold base with a spanner.
When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and/or human injury. 6. Consider a possible loss of power source.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Mounting Caution Caution For M5, 10-32UNF For G Thread (Face seal type) Tightening method Chamfered area for female thread (Recommended value) 1. Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm.
If the panel mount adapter is pulled forward with the hook caught, the product and the adapter may be damaged. -16No.PS-OMU0006-D Piping Tightening the connection thread For connecting to the body (piping specification: -M5) After hand tightening, apply a spanner of the correct size to the spanner flats of the piping body, and tighten with a 1/6 to 1/4 rotation.
Spring 134313 o AWM Dimensions AWD K A Model ARJ1020F-M5-04 ARJ1020F-M5-06 21 22 B 10.4 12.8 C 4 6 D E F 10.6 (Width across flats: 10) G H J Caution 17.2 M5 X 0.8 6 3.5 15.5 50 ITV qRelease the lock to adjust the pressure. After the adjustment, engage the lock. Failure to observe this procedure could damage the handle or cause the secondary pressure to fluctuate.
Series 25 19 dB (A) Page 5-10-4 VEX AN101-01 AN110-01 AN120-M5 AN120-M3 BC sintered body type Ideal for the exhaust of a compact valve or pilot air. 16 dB (A) 21 dB (A) 18 dB (A) 13 dB (A) 100 m AN Page 5-10-5 Silencers Exhaust Cleaner 70 m AMC One-touch fitting connection type Can connect with One-touch fitting directly. 25 dB (A) 30 dB (A) It differs depending upon the model.
OUT OUT Proper Auto Switch Mounting Positions (Stroke End) Proper Auto Switch Mounting Positions(Series CE1) Auto switch (mm) Bore size (mm) Auto switch model Symbol 20 32 40 50 63 12 A B A B A B A B A B A B A B A B A B 40.5 47 55 79 82 85.5 D-A7, A8 4 13 17 39 44 41.5 41 47.5 55.5 79.5 82.5 86 D-A7lH, A80H, A73C, A80C, D-F7l, J79, F7lV, J79C 4.5 13.5 17.5 39.5 44.5 42 A B 38 44.5 52.5 76.5
Valve model Port size L J H G F E D C A B VCW20-12-01A VCB2 1/8, 1/4 13 6 4.5 5 12.8 12.8 30 25 40 34 VCW30-12-02A 1/4, 3/8 19 7 5.5 6 19 19 40 30 52 42 VCB3 VCW30-12-04A 1/2 23 7 5.5 6 23 23 44 36 56 48 VCW40-12-02A 1/4, 3/8 19 7 5.5 6 23 23 40 30 42 52 VCW30-12-04A VCB4 1/2 23 7 5.5 6 23 23 44 36 56 48 VCW40-12-06A 3/4 26 7 5.5 6 28.2 28.2 53 44 56 65 Two mounting screws (for mounting
M5 A 3(R) EXE H A mm Model A B C D E Fn Fd G H XLDV25 50 123 48 41.5 7.5 40 26 38.5 XLDV40 65 170 66 53.5 15.0 55 41 48.5 XLDV50 70 183 79 57.5 17.5 75 52 55.0 XLDV63 88 217 100 72.2 20.0 87 95 70 66.5 XLDV80 90 256 117 82.6 26.5 114 110 83 75.0 XLDV100 108 321 154 95.2 38.0 134 130 102 93.5 XLDV160 138 335 200 101.2 40.0 190 180 153 116.5 10 XL-OMM0005-A 6 Period and Scope of Warranty The
06 6 (mm size) KJH06-M5 Specifications Model PPA100 for high press.
If adjustment is performed at a pressure other than atmospheric pressure, the correct value will not be displayed. 4. Tighten One-touch fittings in accordance with the following. One-touch fittings should first be tightened by hand, and then further tightened approximately 1/6 of a turn using a tightening tool.
type Piping 6/4 (2) 6/4 8/6 8/6 Built-in One-touch fittings Rod end male thread CUJ With rubber bumper CU With boss in head side Through-hole (Standard) Mounting CQS Both ends tapped style Built-in magnet CQM (1) M5 x 0.8 Rc 1/8 Rc 1/8 Rc 1/4 Rc 1/4 Rc 3/8 Rc 3/8 M5 x 0.8 M5 x 0.8 Piping Screw-in type CQ2 Rod end male thread JIS Symbol Double acting, Single rod JIS Symbol With
AS1200-M3 AS1400-M3 AS120-M5 AS220-01AS220-02 AS320-03 AS420-04 10-32UNF Port size M3 x 0.5 2.5, 4, 6 1.05 MPa 0.7 MPa 0.1 MPa M5 x 0.8 1/8 1/4 20, 25, 32, 40 3/8 1/2 6, 10, 15, 20, 25 80, 100 32, 40, 50, 63 Applicable cylinder bore size (mm) 1.5 MPa 1 MPa 0.1 MPa Proof pressure Max. operating pressure Body swivels 360 Swivel type allows free setting of piping.
Such a place is likely to cause a malfunction or breakage. 6. Do no use this product near sources that generate a surge which exceeds the benchmark test, even though this product is CE-marked certified.
A MPa ON kPa OUT1 OFF OUT2 CH 1 2 3 4 PRESSURE Min. B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when work piece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min. B: Minimum pressure value when work piece is not adsorbed. OUT1 auto preset For adsorption verification: In this mode, repeat the adsorption and release of the work piece for a few times.
Contact SMC beforehand and take special consideration of A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
AN120-M5 KJS04-M5 VQZ200/2000 KQ2S06-01S INA-25-46 IN-457-32(6 ) VQZ300/3000 KQ2H08-02S AN101-01 KQ2H06-01S 3 3 3 3 VQZ VQZ VQZ VQZ 82 82 82 82 ,N.C.