For Dry Air, Pilot Operated Series VQ20/30 2 Port Solenoid Valve Turn it right to release. 3.8 Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable. PUSH TURN Precaution Insert/remove the connector vertically, not at an angle.
This convenient feature can be adapted for many applications where reed or solid state switches are desirable. .ManystylesofSwitchesfromwhichtochoose,inc|udingthenewtwoco|or switch for optimum autoswitch placement. 3)TheNCQTresu|tsinlowmaintenancecostwithitsnon-|ubeoperation,|ong life and low initial cost. CAUTION: 1) Be sure all tubing and fittings are clean and clear' 2.
For 12 V or less DC, positive (+) and negative () can be connected in either direction. Grommet type Bushing Red (+) Black () Surge voltage suppressor DIN terminal type The bushing may be damaged if the tightening torque of 0.8 Nm is exceeded. In the event that damage does occur, be sure to replace the bushing.
This convenient feature can be adapted for many applications where reed or solid state switches are desirable. .ManystylesofSwitchesfromwhichtochoose,inc|udingthenewtwoco|or switch for optimum autoswitch placement. 3)TheNCQTresu|tsinlowmaintenancecostwithitsnon-|ubeoperation,|ong life and low initial cost. CAUTION: 1) Be sure all tubing and fittings are clean and clear' 2.
In particular, when using a resin tube, make sure that the size would not be smaller than the port size. (Example: If ID60 is connected to a 12 tube, air supply may not be sufficient and it may cause malfunction due to the unstable operation of the check valve. 2. Replace the element of the mist separator, installed on the inlet side, on a regular basis.
At that time, insulate the lead wires that will not be used. 6. Because this is an open style, it cannot be used where water or oil splashes. 7. It cannot be used if a water hammer or pulsation pressure is applied to the fluid. 8.
O When the unit is used in a dusty location, provision should be made to prevent dust lrom entering the unit by installing silencers to the EXH ports. O The valve may be used in low temperature applications down to 26'F itthe air is sutficiently free ot moisture. Please use an appropriate dryer to ensure dry air and prevent the valve lrom lreezing.
If there is a likelihood that the coolant water will be frozen, drain the coolant water to prevent damage. Also, drain the coolant water when the equipment will not be used for a long period of time. 3. If the cooling performance has been reduced, clean the inside of the coolant water pipes.
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.) Note 7) This product conforms to the CE marking. 302
O When the unit is used in a dusty location, provision should be made to prevent dust lrom entering the unit by installing silencers to the EXH ports. O The valve may be used in low temperature applications down to 26'F itthe air is sutficiently free ot moisture. Please use an appropriate dryer to ensure dry air and prevent the valve lrom lreezing.
O Cannot be used in magnetically contaminated areas. 6 10 15 56kgf-cm. 20 30 35 O lf auto switch cylinders are used in parallel keep the distance between cylinders in accordance with the chart below. To set switch position, loosen the screw and move the switch to the correct position.
methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used.
If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
If a small flat head screwdriver is inserted between the opening in the bottom, terminal block (3) will be removed from the cover (2). (Refer to Figure (1).) 4) Remove the cable gland (4) and plain washer (5) and rubber seal (6). 2.
If a small flat head screwdriver is inserted between the opening in the bottom, terminal block (3) will be removed from the cover (2). (Refer to Figure (1).) 4) Remove the cable gland (4) and plain washer (5) and rubber seal (6). 2.
Note 2) Compared with AR25 type, its adjusting spring will only be changed for 0.2 MPa.
If it is installed on the inlet side and used when the pneumatic pressure is low, the air dryer's dehumidifying capacity cannot be put into full play. (For details, refer to the performance line graph in this section.) Conditions/Inlet air pressure 0.7 MPa Inlet air temperature 30C Precautions Pink Be sure to read before handling.
It is suitable for use in cases where water must be removed, but the air does not have to be as dry as when an air dryer is used or an air dryer cannot be used because an electric power supply is not available.