SMC Corporation of America
Elite Part Number Search
Search Results "LEFB32ET-2000BC-R3"

RW w 1 U nused RW r1 U nused RW w 2 U nused RW r2 U nused RW w 3 U nused RW r3 U nused O ut put dat a occupi es 4 w ords, but uses onl y t he 1st w ord act ual l y. The pressure i s set by b15, b1, b0 dat a. ( b11 b0 cover 100% F. S. ) The l i m i t i s 1198h, dat a of 110% , but t he guarant eed accuracy i s up t o 100% F. S.

OUT port Mounting VBA1: Tightening torque of 12 to 14 Nm (R1/4) VBA2: Tightening torque of 22 to 24 Nm (R3/8) Drain port Rc1/4 (4) O-ring : Mount the O-ring in the groove on the joint of the tank at the back of the booster regulator.

VBAT-M35C () () 1 1 1 1 SMC ( 3 ) VBA2 VBA1 () 30 IN 1.5MPa VBA1A 2MPa, O 1.5MPa OUT VBATA1--X104 VBAT-V1 OUT 4 11 () 1 VBAT05A1-U-X104 VBAT10A1-U-X104 1.5MPa Q235B 5L 10L 075 6.6kg 11.5kg IN 3/8 VBAT-V1 OUT 3/8 1/2 1/4 VBA1 VBA1/VBA2 TSG R0003-2007 2 () IN (I) :VBA1 4VBA2 8 6 : OUT VBA2 (J) Rc3/8 VBA1 OUT IN Rc1/2 Rc3/8 () OUT VBA1 12~14Nm(R1/4) VBA2 22~24Nm(R3

VBA2: Tightening torque: 22 to 24 Nm (R3/8) VBA4: Tightening torque: 28 to 30 Nm (R1/2) (3) Change of the booster regulator OUT port plug VBA2, 4: Tightening torque: 24 Nm (M10) booster regulator by applying the seal tape. with a monkey spanner. Booster regulator Air tank Groove O-ring (4) O-ring

T-X104 VBA4 4 VBA2 1 O VBA4 1 1 / VBAT-T 1 1 1 / VBAT-M36 / VBAT-M36C () () 1 1 1 SMC ( 3 ) () 30 IN 1.0MPa OUT VBATA1--X104 O VBAT-V1 OUT 4 13 () 1 VBAT20A1-T-X104 VBAT38A1-T-X104 1.0MPa Q235B 22L 38L 075 15kg 26kg VBAT-V1 IN 1/2 OUT 1/2 3/4 1/4 VBA2/VBA4 TSG R0003-2007 2 () IN :VBA2 8VBA4 8 10 (I) 6 : Rc3/8 OUT (J) OUT Rc1/2 IN Rc1/2 () OUT VBA2 22~24Nm(R3

There should be no damage or dust for VBA1 is with nominal size 4 and 6, for VBA2 with : Tighten the optional safety valve and drain (3) (2) (1) (4) Booster regulator VBA1: Tightening torque of 12 to 14 Nm (R1/4) VBA2: Tightening torque of 22 to 24 Nm (R3/8) VBA1 VBA2 (3) Change of the booster regulator OUT port plug valve with a monkey spanner. booster regulator by applying the seal tape

Chiyoda-ku, Tokyo 101-0021 JAPAN 417 367 VBA11A 391 328 Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 180 460 454 2010 SMC Corporation All Rights Reserve Rc1/4 URL http://www.smcworld.com Rc3/8 VBAT05S1 VBA10A VBAT10S1 VBA20A VBA22A VBA10A VBAT10S1-VBA2 IN OUT VBA2 VBAT05S1VBAT10S1VBA2 OUT VBA1 2 () VBA1 IN OUT OUT OUT VBA1 OUT IN IN :VBA1 4VBA2 8 O : VBA1 12~14Nm(R1/4) VBA2 22~24Nm(R3

VBA2: Tightening torque: 22 to 24 Nm (R3/8) VBA4: Tightening torque: 28 to 30 Nm (R1/2) (3) Change of the booster regulator OUT port plug VBA2, 4: Tightening torque: 24 Nm (M10) booster regulator by applying the seal tape. with a monkey spanner. Booster regulator Air tank Groove O-ring (4) O-ring

4-14-1 , Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Rc1/4 477 429.8 527 479.8 481 531 206 674 520 256 824 570 Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 2010 SMC Corporation All Rights Reserve IN (I) URL http://www.smcworld.com VBAT20S1 VBA40A VBA42A VBAT38S1 VBA40A VBA42A VBA20A VBA22A VBA20A VBA22A VBA4 VBA2 2 () OUT OUT OUT IN OUT IN :VBA2 8VBA4 8 10 O : IN VBA2 22~24Nm(R3

NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 or loosen the threads. (3) Reuse Normally, fittings with a sealant can be reused 2 to 3 times. Caution (4) Once the fitting has been tightened, backing (1) Be certain to wear safety glasses at all times it out to its original position often causes the sealant to become defective.

R3/8, NPT3/8, G3/8 22 7/8 R1/2, NPT1/2, G1/2 27 1-1/16 (4)For M5, 10-32UNF Tightening method First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. Refer to the table below for reference values.

Not recommended Not recommended Connection thread size Tightening torque [Nm] b) If the fitting is tightened with excessive torque, R1/4 812 R3/8 1520 a large amount of sealant will seep out. Remove the excess sealant. c) Insufficient tightening may cause seal failure, or loosen the threads. d) Reuse 1. Normally, fittings with a sealant can be reused 2 to 3 times. 2.

Warning Male thread Tightening torque [Nm] R3/8 22 to 24 1. Install a stop valve on the supply pressure side of the blow gun. 5. Allow extra length when connecting a tube to accommodate changes in tube length due to pressure. It will be emergency shut off in case of unexpected leakage or damage. 6.

Series: LEFS, Accuracy: Basic Type, Size: 16, Motor Mounting Position: In-line, Motor Type: E (Battery-less absolute, 24VDC, Step), Lead: A (Size 16: 10mm, Size 25: 12mm, Size 32: 16mm, Size 40: 20mm), Stroke: 150mm, Motor Option: w/o Option, Auto Switch Compatibility: None, Grease Application: With, Positioning Pin Hole: Housing B Bottom, Actuator Cable Type, Length: R3 (3m)

Series: LEFS, Accuracy: Basic Type, Size: 16, Motor Mounting Position: In-line, Motor Type: E (Battery-less absolute, 24VDC, Step), Lead: A (Size 16: 10mm, Size 25: 12mm, Size 32: 16mm, Size 40: 20mm), Stroke: 300mm, Motor Option: w/o Option, Auto Switch Compatibility: None, Grease Application: With, Positioning Pin Hole: Housing B Bottom, Actuator Cable Type, Length: R3 (3m)

Accuracy: Basic Type, Size: 32, Motor Mounting Position: L (Left Side Parallel), Motor Type: E (Battery-less absolute, 24VDC, Step), Lead: A (Size 16: 10mm, Size 25: 12mm, Size 32: 16mm, Size 40: 20mm), Stroke: 100mm, Motor Option: w/o Option, Auto Switch Compatibility: None, Grease Application: N (w/o, Roller Specification), Positioning Pin Hole: Housing B Bottom, Actuator Cable Type, Length: R3

Size: 16, Motor Mounting Position: R (Right Side Parallel), Motor Type: G (High Performance, Battery-less Absolute), Lead: A (Size 8: 10mm, Size 16: 12mm, Size 25: 16mm), Stroke: 100mm, Motor Option: C (w/o Lock), Actuator Cable Type, Length: R3 (3m), Controller: CPH (PROFINET), Mounting: 8 (DIN Rail)