PF3WBCSR.eng a place that will be used as a scaffold during piping.
Also suited for use in areas in which water splashes, such as food processing equipment or car washers. Bore size (mm) 20 E1 E2 NN1 M22 X 1.5 NN2 M20 X 1.5 22 0 0.033 20 0 0.033 These dimensions and other dimensions are the same as standard style.
Material 20 25 32 40 Piston seal NLP-20A NLP-19A NLP-32A NLP-40A NBR !
It depends on the actuator type and the lead. 2) Direct Teaching cannot be performed on an actuator with lock as the lock is held even when the servo is turned OFF.
(b) [F 1] Setting of OUT1 The default setting is as follows. If no problem is caused by this setting, keep these settings. Item Default setting The following instructions must be followed during maintenance: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance work Otherwise an injury can result.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
Furthermore, it cannot be used as an emergency cutoff valve. Terminal deceleration and an intermediate speed change circuit can be produced easily. Universal porting could be used as a selector/divider valve. The simple system configuration permits sharp response. The large capacity system configuration without connection loss allows the use of smaller valves and piping.
The Booster Lube cannot be used in an environment or in a location that is exposed to synthetic oil, thinner, acetone, alcohol, organic solvets such as ethylene chloride, chemicals such as sulfuric acid or nitric acid, cutting oil, kerosene, gasoline, or a threadlock agent, etc., because they will be damaged. F.R.L.
This function stores the measuring pressure that is set during the auto preset mode as a basic value. While the current setting is displayed, press the UP or DOWN button to select it as an auto preset setting.
Example: D12BS Note 2) Indicate DIN rail length as D ( indicates stations). Example: D08 In this case, an eight station DIN rail will be provided regardless of the number of manifold stations. Note 3) Indicate wiring specifications on a manifold specification sheet.
less 250 x 250 18 625 or less 282 Body size under 100 to 150 350 or less 300 x 300 20 900 or less 339 20 to 350 under 150 to 200 400 or less 23 Over 900 under 200 to 250 450 or less Order a thickness equal to or greater than that shown on the table.
(made by SMC) Operating ambient temp: -10 to +50 oC Storage ambient temp: -20 to +60 oC 1: Input terminal are not isolated from Power source. 2: Do not connect outside Power source to Input and Output terminals. 62 63 0 1 1 1 1 1 1 1 1 1 1 1 Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Solenoid Specifications Apparent power (VA) Inrush Holding Power consumption (W) (Holding) Temperature rise (C ) (Rated voltage) Frequency (Hz) 50 25 12 60 20 8 Model Power source 5 50 3.5 35 6 50 8 55 6.5 45 8 50 0.5 60 9.5 50 11.5 55 Note) They are values in an ambient temperature of 20C 5C and application of rated voltage.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
o uss cl63n liltrd an the supPly eurrent 4-wire: Input signal of 0-20(mA) Power supply ot l215(V) Current 4-wire: 0-20 mA Input impedance: 200(c,) quivalent 3 TheAir Filterand Nrist SeDaratorshould be maintained periodically.
These units cannot be used in an environment or in a location that is exposed to synthetic oil, thinner, acetone, alcohol, organic solvents such as ethylene chloride, chemicals such as sulfuric acid or nitric acid, cutting oil, kerosene, gasoline, or a threadlock agent, etc., because they will be damaged.
As soon as the work piece is moved within the detection range of the AirCatch Sensor the back pressure P2 increases. If P2 is equal or greater than P1, the switch output is ON. As soon as the work piece is outside of the detection zone the switch output is OFF. Gap too small Green 2 a Place the gap gauge on the detection nozzle for precise adjustment. s Confirm applied air pressure.
. 30 10, 20, 30, 40, 50, 75, 100 40 10, 20, 30, 40, 50, 75, 100 Bore size Strokes are available in 1 mm increments by installing spacers in standard stroke cylinders. 10 16 20 25 30 40 10 mm 16 mm 20 mm 25 mm 30 mm 40 mm Port thread type M thread Rc NPT G 10 to 20 Nil 25 to 40 TN TF Series MQQ is not auto switch capable.
M16 x 1.5 16 M5 x 0.8 M6 x 1.0 76 60 41 32 25 16 12.5 20 M20 x 1.5 16 l M5 x 0.8 M6 x 1.0 90 70 50 40 31.5 20 16 20 M24 x 1.5 20 C B series rod M6 x 1.0 M8 x 1.25 145 115 75 60 E 40 30 20 24 M30 x 1.5 31.5 dH10 L L M6 x 1.0 M8 x 1.25 145 115 75 60 40 30 20 24 M39 x 1.5 31.5 M8 x 1.25 M10 x 1.5 185 145 95 80 50 40 25 26 M48 x 1.5 40 H+0.4 +0.1 D M5 x 0.8 M6 x 1.0 76 60 41 32 25 16 12.5 20
The connection method is as above. 1 If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident. Connector pin No.