60 H A 30 ZPNA-M22 34.6 Bolts Dimensions (mm) A 11 d M3 x 0.5 12 7 M4 x 0.7 B 5.5 L 8 8 10 15 8.5 M5 x 0.8 13-11-82
Cylinder Speed Chart Bore size Series CS1/CS2 Pressure 0.5 MPa, Load factor 50% Cylinder stroke 300 mm Average velocity (mm/s) System 125 140 160 180 200 250 300 1000 Vertically upward movement Horizontal movement 900 800 700 600 500 400 300 200 100 0 A 800 900 1000 700 600 500 400 300 200 100 0 B 900 1000 800 700 600 500 400 300 200 100 0 C 800 900 1000 700 600 500 400 300 200 100 0 D 800
) L6 L8 Note 4) A2 M L7 L4 A1 Note 4) Weight (g) Note 5) Note 1) d D3 MAX.
ECC-PNAL-20MT-D ECC-PNAL-20MR-D ECC-PNAL-20MR-A ECC-PNAL-10MT-D ECC-PNAL-10MR-D ECC-PNAL-10MR-A ECC-PNAL-6MR-A Please Note: 1) All PneuAlphas need to be connected to a power supply. 4/2 : 6/4 : 12/8 suitable to their rated voltage specifications. 2) Stand alone controllers can be programmed from the 8 front panel function keys. 3) All Pneu Alpha controllers have a CD-ROM supplied giving
Stainless Steel (mm) A B C D E F G H J L Bracket part no.
A D A D Data symbol Correction factor Data symbol Correction factor Condition Condition A A Inlet air temperature Inlet air temperature 68F (20C) 1.36 86F (30C) 1.11 Ambient temperature Ambient temperature 77F (25C) 1.07 86F (30C) 1.00 B B C C Outlet air pressure dew point Outlet air pressure dew point 37.4F (3C) 0.50 41F (5C) 0.67 Inlet air pressure Inlet air pressure D F D F 145psi (1 MPa
Analog Voltage Output (1 to 5 V) Analog Current Output (4 to 20 mA) 5 20 Analog output [mA] Analog output [V] Model Max. rated flow value [l/min] Model Max. rated flow value [l/min] PFM710--C/E PFM725--C/E PFM750--C/E PFM711--C/E PFM710--D/F PFM725--D/F PFM750--D/F PFM711--D/F 10 10 (5) 1 4 25 25 (12.5) 50 50 (25) 00 0 0 100 100 (50) Max. rated flow value Max. rated flow value ( ): Fluid
BM2-032 BM2-040 D-C7, D-C8, D-H7 D-B5, D-B6, D-G5 D-A3A, D-A44A, D-G39A, D-K39A BM2-020 BM2-025 BA2-032 BA2-040 BA2-020 BA2-025 BM3-032 BM3-040 BM3-020 BM3-025 Caution Mounting Type and Accessories 1. Be careful of the snap ring springing out. When replacing the rod seal, take care that the snap ring does not spring out while you are removing it.
d C C B H B H Material: Carbon steel Material: Carbon steel Part no.
Recommended tightening torque Auto switch model Recommended tightening torque [Nm] D-M9 0.05 to 0.15 D-M9A (Water resistant) 0.05 to 0.10 Fig. 8 D-F8 0.10 to 0.20 Set screw Auto switch 29 - Auto switch proper mounting position at rotation end Table 11 Auto Switch Rotation range / Actuation / most sensitive position A A A A B B B B D-M9 D-F8 Magnet Operation range at optimum set position (
Position code (Order #1 #4, Port A D) Message code #4 #3 #2 #1 D C B A 0 0 1 0 0 0 0 1 0 0 0 1 Message code 0x2 Product No.1 A port Ex.: Short-circuit or over current error with the first slave of COM A port. Message code and corrective action for diagnostic error are shown below.
Note3) L6 L8 Note 4) A2 M L7 L4 A1 Note 4) Weight (g) Note 5) Note 1) d D3 MAX.
Enter in order starting from the first station on the D side.
Enter in order starting from the first station on the D side.
Enter in order starting from the first station on the D side.
Without auto switch (Without built-in magnet) Remarks Symbol Heater Temperature 16 D-M9N(M)(L)(Z) D-M9P(M)(L)(Z) D-M9B(M)(L)(Z) D-A90(L) D-A93(M)(L)(Z) M9N(M)(L)(Z) M9P(M)(L)(Z) M9B(M)(L)(Z) A90(L) A93(M)(L)(Z) M9// Nil H0 H4 H5 5 to 60C None None With 100C heater With 120C heater Solid state auto switch 5 to 150C Reed auto switch (Not applicable to flange size 16) Note) Size 16 is not
NOTE The parameter for output modules takes priority over the system parameter [IO communication on port diagnostic (COM A-D)].
Controller (VYU5-D) External appearance of exclusive controller RUN1 STOP START SEL. SW RESET RUN2 RUN1 OV INPUT 6 7 5 8 4 + 9 3 SET UP A 2 B 1 0 C D 1 E F 0 to 10V V R 1 OUTPUT SET UP BALANCE CONTROLLER VYU5-D 2 V R 2 OV ERR.
BBA4: D-C7/C8/H7 "D-H7BAL" switch is set on the cylinder with the screws above when shipped.