Speed Controller with One-touch Fitting Stainless Steel Type Elbow Type/Universal Type AS-FG Series Push-lock type

Connection Female Thread: G Uni thread size Wrench tightening angle after hand-tightening [deg] Tightening torque [Nm] 1/8 30 to 45 3 to 4 1/4 15 to 30 4 to 5 3/8 15 to 30 8 to 9 1/2 15 to 30 14 to 15 Winding direction Sealant tape Expose approx. 1 thread 2. The gasket can be reused up to 6 to 10 times.

Vacuum Pad with Ejector ZHP Series Pad Diameter: ø63, ø80 ZK2 ZQ Ejector and pad are integrated. ZR Space saving and reduced piping labor! Bellows type with groove ZB ZA Two-stage ejector ZX More efficient ejector 30% reduced 50% increased ZM Air Suction

20 10 0 100 Suction flow [L/min(ANR)] Air consumption [L/min(ANR)] Vacuum pressure Vacuum pressure [kPa] Vacuum pressure [kPa] 80 60 Suction flow 40 20 Air consumption 0 0 10 20 30 40 Supply pressure [MPa] Suction flow [L/min(ANR)] ZHP-10 ZHP-10 (Supply pressure: 0.35 MPa) 100 90 80 70 60 50 40 30 20 10 0 0 0.1 0.2 0.3 0.4 0.5 0.6 100 90 80 70 60 50 40 30 20 10 0 100 Suction flow [L/min(

Sensor Monitor

Page 30 [F 0] Units selection function -53No.PS-OMW0014-B [F80] Power saving mode Power saving mode can be selected. When selected and no buttons are pressed for 30 seconds, the product will shift to power saving mode. Press the UP or DOWN button in function selection mode to display [F80]. Press the SET button. Move on to power saving mode.

Sensor Monitor

N.C. -14No.PS-OMU0012-C Internal circuit and wiring example Setting of NPN open collector 2 outputs: Pressure sensor 3-wire type Max. 30 V, 20 mA Residual voltage: 1 V or less Setting of PNP open collector 2 outputs: Pressure sensor 3-wire type Max. 20 mA Residual voltage: 1 V or less Setting of NPN open collector 2 outputs: Pressure sensor 2-wire type Max. 30 V, 20 mA Residual voltage: 1

PFxx-OMP0001CN

IN(66) IN OUT OUT IN 8cm () Rc1/2NPT1/2Rc3/4NPT3/4 2830 Nm 1/2 30 mm 3/4 35 mm 9mm 2F.S. -16No.PF-OMP0001CN-F FG 1 DC(+) 2 OUT2// 3 OUT1 4 DC(-) -17No.PF-OMP0001CN-F NPN(2 ) PFMB7--ADC(+) OUT1 OUT2 DC(-) 28 V 80 mA 1 V NPN(1 )(15 V) PFMB7--CNPN(1 )(420 mA) PFMB7--DDC(+) OUT1 DC(-) 28 V 80 mA 1 V C15 V 1 k D420 mA 600 NPN(1 ) PFMB7--GDC(+) OUT1 DC(-) 28 V 80 mA 1 V 0.4V ()30 msec

Voltage Monitor for PFMV5

Do not use a cable longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply.

XMD/XYD Series

Bonnet assembly/construction part number:1 Valve size Temperature specifications 25 40 50 63 80 Caution General use XLD25-30-1 XLD40-30-1 XLD50-30-1 XLD63-30-1 XLD80-30-1 High temperature XLD25-30-1H XLD40-30-1H XLD50-30-1H XLD63-30-1H XLD80-30-1H Note1) The magnet for auto switch is not provided. When the magnet for auto switch is necessary, add -M9// at the suffix of the part number.

AC Servo Motor Driver (Pulse input type/Positioning type)

Recommended Parameter Values [LEF] LEFS25 LEFS32 LEFS40 Series Lead symbol H A B H A B H A B Lead 20 12 6 24 16 8 30 20 10 Initial value Recommended Value Parameter *1,*2 Para No Number of command input pulses per revolution *3. PA05 100 100 Electronic gear numerator *3. PA06 1 100 (Positioning mode: 10) Electronic gear denominator *3.

LEKF-OMZ0035

Slider type LEKFS series 2.1 Specification AC servo motorMotor typeS*/T*) Model LEKFS25 LEKFS32 LEKFS40 Stroke [mm] 100 to 500 100 to 500 200 to 600 Horizontal 10 20 20 30 40 45 30 50 60 Work load [kg] Note1) Vertical 4 8 15 5 10 20 7 15 30 Up to 400 1500 900 450 1500 1000 500 1500 1000 500 401 to 500 1200 720 360 1500 1000 500 1500 1000 500 501 to 600 900 540 270 1200 1000 500 1500 1000

High performance type Step Motor Controller (Servo/24 VDC)

Make sure to allow intervals of 15 ms or longer (30 ms is recommended) between input signals, and maintain the input state for the same period of time. 30 No.JXC-OMY0002-A -Output terminalNo. Function Description B1 OUT0 When the operation is started and DRIVE is turned OFF, a Bit no. corresponding to the number of the active step data will be output from these terminals.

JXCx-OMT0062

Leave an interval of a minimum of 15 ms (recommendation is 30 ms) between input signals and maintain the state of the signal for a minimum of 15 ms (recommendation is 30 ms), because PLC processing delays and controller scanning delays can occur. 12.4 Controller input signal response Signal timing Check the timing of the signal from the PLC to the controller. time When power is applied,

Digital Pressure Switch

(Refer to "List of output mode" on page 30.) The ability to withstand a voltage applied between an electrical circuit and the body. If more voltage is applied to the product, the product may be damaged. (voltage mentioned here is not power voltage to activate the product).

IZ-OMK0015

Ion balance OK LED Within +/-30 V Lighting (or Flash) Outside of +/-30 V Goes off * OK LED Flashes when the offset voltage is near the adjusting target to notify the emitter maintenance timing is coming soon. ALARM LED: Indicates the abnormal states of the ionizer. Model Nu File 00 LED name Function HV Indicate that abnormal current flows to the emitter.