IO-Link/ELECTRO-PNEUMATIC REGULATOR Error "0" is displayed when Bit 11 to 14 of the Bit offset are "0." "1" is displayed when any other part of the Bit offset is "1." 9 - Process data output: 2 BYTE (base module --> device (ITV)) The product adjusts the pressure to the set value. 0 1 BYTE 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit Set pressure value. (16Bit) Value * Data is adjustable up to 120%F.S.
Corresponding international standard: ISO/DIS 2380-1,ISO 2380-2 (15) ASB-*BD series lock nuts do not have stop mechanical, so if you loosen them while pulling on the lock nut, the lock nut may detach from the needle.
No.PS-OMU0002CN-D // ZSE20A(F) ISE20A 2 8 10 11 15 15 17 19 [] 22 23 3 24 26 28 28 28 F0 30 F1 OUT1 31 F2 OUT2 34 F3 36 F4 37 F5 FUNC 39 F6 41 F10 42 F11 48 F80 49 F81 50 F82 52 F90 53 F96 55 F97 56 F98 58 F99 60 61 65 65 66 75 75 78 -1No.PS-OMU0002CN-D 1 (ISO/IEC)(JIS) *1) *2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO
No.PS-OMU0005CN-C // ZSE20B(F) ISE20B 2 8 10 11 15 15 17 20 [] 23 24 3 25 27 29 29 29 F0 31 F1 OUT1 32 F1 OUT2 35 F3 37 F4 38 F5 FUNC 40 F6 42 F10 43 F11 49 F80 50 F81 51 F82 53 F90 54 F96 56 F97 57 F98 59 F99 61 62 66 66 67 76 76 79 -1No.PS-OMU0005CN-C (ISO/IEC)(JIS) *1) *2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO
)1 1 2kPaMPa 1 ZS-24-A A M35 L,M45 L, 2 ZS-24-D D M35 L,M45 L, 2 / V100-49-1-1 300 mm() V100-49-1-2 500 mm() V100-49-1-3 1000 mm() V100-49-1-4 2000 mm() V100-49-1-7 5000 mm() PCA-1557772 3000 mm() -11No.PS-OMM0006CN-E LCD (UP) (SET) (DOWN) () LCD 4 (UP)ON/OFF (DOWN)ON/OFF (SET) -12No.PS-OMM0006CN-E 2 ON/OFF 2 7 "8"7 "-"()7 digit() 1 digit=1 kPa 1,2,3,,99,100 1 kPa 15
No.PS-OMV0003CN-G / / ISE70--L2 ISE71--L2 2 8 9 11 14 14 15 17 19 20 3 21 23 25 25 25 F0 27 F1 OUT1 29 F2 OUT2 32 F3 34 F4 35 F6 37 F10 38 F11 44 F14 Zero-cut 45 F80 46 F81 47 F90 49 F96 51 F98 52 F99 54 55 IO-Link 60 IO-Link 60 60 61 IO-Link 64 72 72 73 82 84 -1No.PS-OMV0003CN-G (ISO/IEC)(JIS) *1) *2) *1) ISO 4414: Pneumatic fluid power -General
Preparation before piping 1/8 30 to 45 3 to 4 Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe. 3/8 15 to 30 8 to 9 1/2 15 to 30 14 to 15 2) The gasket can be reused up to 6 to 10 times. It can be replaced easily when it has sustained damage.
Seal cap 1 pc. seal cap for unused fieldbus interface connector (BUS OUT). 1: For details of suitable cables refer to the Accessories section on page 36. 2: Refer to page 15 for the LED Indication and Settings. -9No.EX-OMN0013-I Installation and Wiring Installation Connect valve manifold to the SI unit.
Investigate the cause of the voltage fluctuation, and take countermeasures against it. 15 to 30 VDC Check that the solenoid valve power supply voltage is within the specified range.
Contents Bore size (mm) Set of left nos. #0, #1, #2, #3, #4 @9 #0 #1 #2 #3 #4 Note 1) Seal kit includes #0 to #4 for 10. @9 to #4 are for 15 to 25. Order the seal kit, based on each bore size. Note 2) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 and 10 g, 15 to 25: 10 g). Order with the following part number when only the grease pack is needed.
Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g). Order with the following part number when only the grease pack is needed.
Sine Rodless Cylinder/Slider Type Series REAL Ball Bushing Bearing: 10, 15 Construction 10, 15 @9 #2 #4 @8 #3 #1 #0 REAL10 The numbers are the same as the "Construction" of the Best Pneumatics No.3 Series REAL. *BLUE links will lead to purchase pages. Seal kit List Description Material Note No. Replacement Parts: Seal Kit Kit no.
Services 15 Sebaai Street, Miami 21411 Alexandria, Egypt TEL: 3-548-50-34 FAX: 3-548-50-34 PAKISTAN (Distributor) Jubilee Corporation First Floor Mercantile Centre, Newton Road Near Boulton Market P.O.