ASx-OMT0060

Application This product is designed to control the speed of a pneumatic actuator. 4.

ＳＭＯＯＴＨ ＣＹＬＩＮＤＥＲ

Take special care to isolate and shield seals from equipment which is apt to generate heat, radiation and ozone. 3) Be careful not to deform and damage seals by piling up a large volume of them or putting weights on them. 4) Note that white powder may appear on the surfaces of rubber parts in storage though it does not affect their performance. 4.

VQ4000/5000 (Pilot Valve V100)

Purify the air source. 4. Air leaks from the manifold 4-1) Loose DIN rail clamp screw Hold manifolds tightly for tightening so that there is no gap between the valves.

Mechanically jointed rodless cylinder With cam follower guide, With single-axis linear guide With double-axis linear guide

However, it is constructed to be used for driving the product body, it may cause failure if it is used solely with a load applied. 2-4. Mounting and Installation 2-4-1. Mounting Surface It is recommended to mount the cylinder on a surface with a high flatness (e.g. a machined surface).

HEC-OM-R008

If using Ethylene Glycol, refer to the suppliers Material Safety Data Sheet [RET]: Used to fix the value changed by [] key. 0 to F (MSDS) and wear Personal Protective Equipment (PPE) as appropriate. 4 Unit Number (Hex decimal) 0 Press again to return to current temperature indication. 4. Fill the circulating fluid into the reservoir.

VFR4000-OMH0003

When installing the products, follow the listed torque specifications. 4. If air leakage increases or equipment does not operate properly, stop operation. Check mounting conditions when air and power supplies are connected.

MHT2

12 (Both sides) 4-M8 x 1.25 thread depth 14 Mounting thread Open 23 Closed 2 MHZ MHF MHL MHR MHK MHS Finger closing port Rc 1/4 Finger opening port Rc 1/4 MHC MHT MHY 4-M10 x 5 bottom hole dia. 8.6 MHW 4-M10 x 1.5 thread depth 12 Mounting thread Thread for mounting attachment MRHQ MHT2-63D Misc.

MHT2

Local Area: (800) 258-9200-www.stevenengineering.com MHS Finger closing port Rc 1/4 Finger opening port Rc 1/4 MHC MHT MHY 4-M10 x 5 bottom hole dia. 8.6 MHW 4-M10 x 1.5 thread depth 12 Mounting thread Thread for mounting attachment MRHQ MHT2-63D Misc.

Mist Separator Series AM Model Series AM can separate and Model AM850 AM250 AM350 AM450 AM550 AM650 AM150 remove oil mist in compressed air Rated flow 750 1500 2200 3500 6000 12000 300 (1) (l/min (ANR)) which is difficult to remove by Port size ordin

Model AM850 AM250 AM350 AM450 AM550 AM650 AM150 Rated flow (l/min (ANR)) 750 1500 2200 3500 6000 12000 300 (1) Port size (Nominal size B) 1/8 ,1/4 ,3/8 1/4 ,3/8 ,1/2 3/8 ,1/2 ,3/4 1/2 ,3/4 ,1 3/4 , 1 1, 11/2 11/2 , 2 0.38 0.55 0.9 1.4 2.1 4.2 10.5 Weight (kg) Note 1) Max. flow capacity at a pressure of 0.7MPa. It varies depending on operating pressure.

CC

In particular, to prevent "4)", use a double side hydro.

3 Port Direct Operated Solenoid Valve Metal Seal, Body Ported 1

dimensions Port size Rc VS A Model B C D E F G H J K L M N P U T S R VS3135-02 VS3135-03 VS3135-04 VS3145-04 VS3145-06 VFN 1 4, 3 8, 1 2 64 64 65 70 1 136 35 9 64 54 19 32 50 50 118 96 120 60 7 1 2, 3 4 82 68 88 92 1 181 53 12 81 70 35 36 66 52 133 96 140 66 9 DC C Model VS3135-02 VS3135-03 VS3135-04 VS3145-04 VS3145-06 A B Port size Rc 1 4, 3 8, 1 2 64 50.8 163 196 68 60.5 1 2, 3 4 4-16

VHS20/30/40/50

H 28 30 36 44 54 G 33 42 44 50 61 F 45 55 58 65 76 E 22 21 26 D 34 46 63 67 78 C 40 53 70 75 90 B 20 29 39 42 53 A 59 78 107 110 134 I 45 55 63 69 81 Model Piping port VHS20 VHS30 VHS40 VHS40-06 VHS50 1/8, 1/4 1/4, 3/8 1/4, 3/8, 1/2 3/4 3/4, 1 5-8-22 5 Series VHS Specific Product Precautions Be sure to read before handling. Air Supply Precautions on Design Warning Warning 1.

SYJA300

Refer to front matters 58 and 59 for Safety Instructions and pages 3 to 7 for 3/4/5 Port Solenoid Valve Precautions. 0.6 JIS Symbol Pilot pressure MPa 2 4 SYJA52 SYJA72 2 4 Pilot pressure range SYJA51 SYJA71 0.5 2 4 2 4 (A) 2 (A) 2 0.4 0.3 1 (P) 3 (R) 1 (P) 3 (R) 0.2 N.C.