EX600-LAB1_LBB1.eng C/Q IO-Link or standard I/O mode 3 4 5 N.C.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
When setting, allow 7 digits or more between Set point 1 and Set point 2 (Set point 3 and Set point 4). 2: When Set point 1 = Set point 2 (Set point 3 = Set point 4), chattering may occur. Set value is calculated and set. Set value 4 Set value or 3 or 3 Measurement mode Do not use the product in a place where static electricity is a problem.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4.
Note4) Figures in ( ) indicates the mass of CF (conflate) fittings. 7 XM-OMP0002-A 4. Construction / Dimensions 4-1.
A B PSE57-01 8 R1/8 PSE57-02 12 R1/4 Lead wire and M12 connector ZS-37-A ZS-37-B -17No.PS-OMS0005-E Adapter with throttle ZS-31-X Model No. D E F G H I ZS-31-X188 20 9 R1/8 Rc1/8 14 1.5 ZS-31-X175 29 13 R1/4 Rc1/4 17 1.6 -18No.PS-OMS0005-E Revision history A: Contents are added. B: Contents are added. C: Contents revised in several places. D: Contents revised in several places.
F.G. 4. 1. 1. 2. 12 10N [102kgfcm] 1. 2032 20N [204kgfcm] () 40,50,63 30N [306kgfcm] 2. 3. 2. 1.52 1. 2. 1. 1()ISO VG32 3. 4. 5. 6. 1. 2.14.5mT CE1 3. 4. (DC1224V) [] 1. 2. 3. 4. 2.
Remove the excess sealant. 4) Insufficient tightening may cause seal failure or loosen the threads. 6 No.V100-OMV0001 V100 Series Precautions for 3 Port Solenoid Valve 4 Be sure to read before handling. 4. If an excessive amount of carbon powder is present, install a mist separator on the upstream side of the valve.
Use the following parts for piping and fittings. <1/4"> Piping Outside diameter 1/4" = 6.35 mm Stainless steel tube Nut Swagelok fittings by Swagelok Company Attached to product (2 pcs each) VCR female nut (SS-4-VCR-1) Gland Swagelok fittings by Swagelok Company VCR gland (SS-4-VCR-3) Gasket Swagelok fittings by Swagelok Company VCR gasket retainer assembly (SS-4-VCR-2-GR) <3/8"> Piping
Application This product is designed to control the speed of a pneumatic actuator. 4.
Take special care to isolate and shield seals from equipment which is apt to generate heat, radiation and ozone. 3) Be careful not to deform and damage seals by piling up a large volume of them or putting weights on them. 4) Note that white powder may appear on the surfaces of rubber parts in storage though it does not affect their performance. 4.
Purify the air source. 4. Air leaks from the manifold 4-1) Loose DIN rail clamp screw Hold manifolds tightly for tightening so that there is no gap between the valves.
However, it is constructed to be used for driving the product body, it may cause failure if it is used solely with a load applied. 2-4. Mounting and Installation 2-4-1. Mounting Surface It is recommended to mount the cylinder on a surface with a high flatness (e.g. a machined surface).