Coolant valve Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used. Reassembly Procedure 1)Insert cable gland (4), washer (5) and rubber seal (6) and housing (2) into cable (7) in order.
/ Power block MODEL / Series / Product Number EX9-OET1 EX9-OET2 EX9-OEP1 EX9-OEP2 EX9-PE1 Table of Contents Safety Instructions 2 Model Indication and How to Order 8 Product Outline 8 Summary of Product elements 9 Product Selection 11 Selection for low wattage and high wattage load 11 EX9-OET (Output block for low wattage load) 13 EX9-OEP (Output block for high wattage load) 14 Polarity 15
As handling involves the risk of a danger of electrocution, injury or fire. 15. Do not use in direct sunlight. Do not use in direct sunlight. It may cause malfunction or damage. 16. Do not use in places where there is radiated heat around 4. Install an external emergency stop circuit that can promptly it. stop operation and shut off the power supply.
Node address SW1 SW2 SW3 SW4 Node address SW1 SW2 SW3 SW4 0 0 0 0 0 8 0 0 0 1 1 1 0 0 0 9 1 0 0 1 2 0 1 0 0 10 0 1 0 1 3 1 1 0 0 11 1 1 0 1 4 0 0 1 0 12 0 0 1 1 5 1 0 1 0 13 1 0 1 1 6 0 1 1 0 14 0 1 1 1 7 1 1 1 0 15 1 1 1 1 0: OFF 1: ON Set the node address so that it does not duplicate the node address of other slaves.
Table 3 Thread size Appropriate tightening torque 1/8 3 to 5 1/4 8 to 12 3/8 15 to 20 1/2 20 to 25 (2) If the product is mounted with excessive 2) The outside diameter of polyurethane tubing torque, some sealant will seep out. Remove the excess sealant. swells when internal pressure is applied; therefore, it may not be possible to re-insert used tubing into One-touch fittings.
(In the case of external pilot specification) (15) Higher voltage or wrong coil used Burnt coil (9) Coil splashed by water (10) Air leaks through EXH. port [3(EB), 5(EA) port] of main valve.
Step 7 Reassembly of bonnet assembly (No.2) 3 Bolt 1 2 4 Bonnet assembly Port 1(P) Bolt size, Tool, Tightening torque of bolt (Nm) valve Bolt size Hex Tightening torque size wrench XLAV-16 M3 3 0.7 -25 M5 4 1.5 -40 M6 5 2.5 -50 M8 6 6.1 Body -63 M10 8 15 -80 Turn ON the solenoid valve to supply air pressure of 0.4MPa (G) to the port 1(P).
Emitter maintenance (cleaning and replacement) . 15 4-5. Alarm function . 17 5. Performance . 18 5-1. Installation distance and Discharge time (Discharge time of 1000V100V) . 18 5-2. Static neutralization range (Discharge time of 1000V100V) . 19 5-3. Pressure Flow characteristics . 20 6. Dimensions . 20 7. Specifications . 22 8.
The allowable upper and lower range of temperature can be set between 0.1 and 10 C. 3.6.9 Warning of output interruption This function raises alarm and stop operation safely when a critical error detected (However, operation continues in case of ERR 15 and ERR 18.). When a alarm is detected, the display shows ERR and a alarm number.
(fluid: Dry air) Temperature characteristics 2%F.S. max. (15 to 35 C) 5%F.S. max. (0 to 15 C, 35 to 50 C) Pressure characteristics 5%F.S. max. (0.35 MPa reference) Rated pressure range -70 kPa to 750 kPa Proof pressure 1 MPa 50 msec. Response time (when "Select response time" wire (white) is connected to GND, response time is 1 sec.)
When using the product at the minimum operating pressure, set the pilot pressure to 0.1 MPa or higher. (15) As a reference, we have confirmed through our durability tests that the check valve has a durability against 10 million cycles of ON and OFF operations and the residual pressure exhaust button has a durability against 10,000 cycles of operation at the maximum operating pressure.
Be Nil 300mm 6 600mm 10 1000mm 15 1500mm 20 2000mm 25 2500mm 30 3000mm 50 5000mm Connector Assembly with CoverDimensions How to Order Enter the part number for a plug connector solenoid valve without connector together with the part number for a connector assembly with cover.
and operating fluid temperature Piston speed Double acting D type 0. 0125 Single acting T type 0. 0062 0. 025 0. 05 0. 1 0. 2 0. 3 Allowable kinetic energy J Non-lube Lubrication Note 1) Double-side Rubber bumper Bumper Double-side rubber bumper +1. 0 0 0.8 0.5 Stroke length tolerance Note 2) Non-rotating accuracy of the rod Allowable rotational torque(Nm) 0. 0015 0. 02 0. 04 0. 10 0. 15