FEP Tubing (Fluoropolymer) At a temperature of 20C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure 2R at the point where the outside diameter's rate of change is 5%.
+10 Basic Air Cylinders 3 4/5 4 Outdoor Pipelines 1 2/3 1 Packaging Machines 3 4/5 3 Hand Air Tools 3 4/6 4 A Series Compressed Air Filters The selection of an air filter should be based on a desired result.
6 !5 SlA Installation !3 !1 VlA 1(P) 2(A) 1(P) 2(A) Warning 1 When exhaust piping is connected to 3(R) port,effective area should be larger than the specified value mentioned in the table below. If it is smaller, air leakage will occur due to back pressure. y q w !4 SlA !7 !4 3(R) VlA !
-2No.PS-OMT0005CN-A / 1 1.5 *3) *3)1 1 [] -3No.PS-OMT0005CN-A () () () () -4No.PS-OMT0005CN-A () * C3604+AI203(96)FKM () ZS-31-X175 X188 () NG NG -5No.PS-OMT0005CN-A * (Nm) R1/4 812 (50N () * () 6 33 ( ) () 10 m DC(-)() FG -6No.PS-OMT0005CN-A * ( ) () CE -1060 * 2030 10 1% * -7No.PS-OMT0005CN-A 7 02 PSE57 / M12(3m) 5 (02MPa) L M12(3m) 6 (05MPa) N 7 (010MPa) (1~5V)
Because tube fittings are provided, use a tube with a bore of 10mm, and keep the overall pipe length within 5m. AMH850 type (N.O) Use a tube with a bore of 9mm or more, and keep the overall pipe length within 2.8m.
Contact P/A regarding the valves 3 to 5.
Avoid direct sunlight by providing a protective cover, etc. 6. When sources of heat are located nearby, block off any radiated heat. Caution 1. It is recommended that the downstream pressure be set in the range of 25 to 85% of the upstream pressure. Mounting Caution 1. Open the sealed package inside a clean room. This product is packaged in sealed double packaging in a clean room.
Avoid direct sunlight by providing a protective cover, etc. 6. When sources of heat are located nearby, block off any radiated heat. Caution 1. It is recommended that the downstream pressure be set in the range of 25 to 85% of the upstream pressure. Mounting Caution 1. Open the sealed package inside a clean room. This product is packaged in sealed double packaging in a clean room.
1 ARP 4 Bonnet PPS 5 Knob PBT IR-A i o Electroless nickel plated 6 Set nut ZDC 7 Valve spring Stainless steel 316 IR 8 Main valve Ceramics !
Use 0.3 to 0.7 times the thrust (differs depending on the operating speed) as a guide for actual use. g: Gravitational acceleration Dynamic moment M Mounting orientation Dynamic load FE Horizontal Ceiling Wall Vertical Z 1.4 100 x a x mn x g a a 1 3 x FE x Z ME Dynamic moment Dynamic moment ME does not occur.
Cooling water (l/min) 180C Inlet air temperature Correction factor Air flow (l/min (ANR)) Model 50C 70C 100C 41.5 43 45.5 37 43 49.5 37 43 45.5 37 42 43.5 40 44 46 39.5 43 44.5 41 43 45.5 A B C A B C A B C A B C A B C A B C A B C 35.5 36 36.5 33.5 36 38 33.5 36 36.5 33.5 35 36 34.5 36 37 34.5 35.5 36 34.5 35.5 36 38.5 40 42 36 40 45.5 36 40 42.5 36 40 41 38 40 42.5 38
It can result in damage of the sensor and accidents. 6. Distance measurement is 50 mm. Use display of label attached to the sensors as a guide. Approx. 50 mm Distance measurement BEST DETECTING POSITION 50mm Detection hole Detection area 7. The measurement of a part with a high-charge potential can be highly dangerous as it can cause a discharge to the users hand.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.