IZ-OMK0015

And Adjust the offset voltage after supplying power. 23 Doc.No.IZ-OMK0015D (11) Timing chart Timing chart of normal operation Normal operation Reset operation Remarks Turn the power off to solve the problem, then supply power again. The error signal(OUT3) will be reset.

E-MY2_E_D

CONTENTS SAFETY 2 General General 3 positions 5 positions Model Indication Method 5 Names and Functions of Individual Parts 6 Installation 9 3 positions Names and Functions of Controller 11 Example of Internal Circuit and Wiring 12 Setting 15 Operation Characteristics 20 Specifications 21 5 positions Names and Functions of Controller 23 Example of Internal Circuit and Wiring 24 Setting 27

Air cylinder

Order for tightening mounting screws 11 2-9-2. Auto switches When an auto switch is mounted or its set position is changed, refer to Fig. 4 to 11. C a u t i o n Use a specific mounting bracket (Page 19, Table 2) . Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDA).

Air cylinder

(Refer to Page 11, 2-6.

REGULATOR

13 90 3.2 AR60K-B 70 66 65.8 11 13 90 3.2 Note 1) B dimension is a size in the state to unlock the handle.

FILTER REGULATOR

AW20-B 11 AW20-B 0.80.1Nm AW30-B 17 AW30-B 2.350.3Nm AW40-B 21 AW40-B 3.50.3Nm Disassembly Remove the bowl assembly, housing, and element. Hexagon Remove a housing from a body by turning 4 mounting screws to the left with a hexagon wrench key. wrench key Nominal5 Remove the valve guide.

Mechanically jointed rodless cylinder With cam follower guide, With single-axis linear guide With double-axis linear guide

Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 10 2.6 Speed Control -P. 11 2.7 Shock Absorbing Mechanism -P. 11 2.8 Directional Control -P. 12 2.9 Mounting of Auto Switch -P. 13 3. Maintenance and Inspection 3.1 Inspection -P. 14 3.2 Maintenance -P. 14 3.3 Replacement Parts -P. 14 4.

VNA Series

Wiring 1) Insert cable gland (4), washer (5) and rubber seal (6) into cable (7) in order, and insert it into housing (2). 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm.

Digital Pressure Switch

Check if the dispersion is within the display accuracy range. 11 Product failure Replace the product. -52No.PS-OML0003-J Fault No. Fault Possible cause Investigation method Countermeasure Install a 5 m filter to prevent foreign matter from entering the pressure port. Also, clean the filter regularly to prevent drainage deposits.

High Vacuum L Type Valve

Not adhering to these specifications, can result in damage to the product. 11 XL*-OMI0013-B 7-2.

XMA/XYA Series

Warranty period and guaranteed range 10 6.Parts replacement procedure 11 1 XM-OMP0001-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.

ncq8mp

SeriesNCQ8 Air Cylinder: Standard Type Double Acting, Single Rod Maintenance Parts 056 to 400 Construction Double Acting, Single Rod 10 11 9 Seal Kit Parts List No. 9 10 11 Description Piston Seal Rod Seal Tube Gasket Material NBR NBR NBR *BLUE links will lead to purchase pages. Repair Parts: Standard Seal Kit for Double Acting, Single Rod Remarks Bore size Kit no.

Rotary Actuated Air Gripper/3-Finger Type MHR3/MDHR3 Series Size: 10, 15

9 P3313128 P3313228 MHR3-10 MHR3-15 Description Cover Main parts MA D533 MHR3/MDHR3 Series Nominal Size 10 Without auto switch: MHR3-10R 3 x M3 x 0.5 thread depth 6 P.C.D.24 (Mounting thread) 120 120 25 25 M3 x 0.5 Finger opening port M3 x 0.5 Finger closing port 44 29 9h9 0 0.036 33.5 1 5 4 16 (36.5) 12 2 2 3e8 0.014 0.028 Open: 11 Closed: 8 8 0 0.05 4 3 x M3 x 0.5 thread depth 6 (Thread