10 to 60C (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)250 VAC for 1 minute between live parts and case2 M or more between live parts and case (at 50 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/s2 in X, Y, Z directions, 3 times each (De-energized)?
OUT1, OUT2: OrangeIP65Operating: 23 to 122F, Stored: 14 to 140F (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)1000 VAC for 1 minute between live parts and case50 M or more between live parts and case (at 500 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/
10 to 60C (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)250 VAC for 1 minute between live parts and case2 M or more between live parts and case (at 50 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/s2 in X, Y, Z directions, 3 times each (De-energized)?
A built-in pressure gauge, mountable at any angle, depending on the piping direction ensures good visibility of the pressure gauge, even when the AWG is mounted at an overhead or underfoot location. Equipped with a special mechanism, the pressure gauge will not be revolved even after the handle is operated.
10%, Ripple (P-P) 10% or less (With power supply polarity protection)17 mA or less at 24 VDC5 ms or less?1% F.S. or lessIP40Operating: 0 to 60C, Stored: ?
OUT1, OUT2: OrangeIP65Operating: 23 to 122F, Stored: 14 to 140F (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)1000 VAC for 1 minute between live parts and case50 M or more between live parts and case (at 500 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/
75 kPa to 0.2 MPa1.1 mm10 ms or less (at pneumatic pressure)Zero leakage, either external or internal (at water pressure)0.3 MPa0 to 50C0 to 50C (with no condensation)18 lFreeIP40 or equivalent20 g12, 24 VDC?10% of rated voltageClass B2 W(0.08 A)InrushHolding50 dB
OUT1, OUT2: OrangeIP65Operating: 23 to 122F, Stored: 14 to 140F (No freezing or condensation)Operating/Stored: 35 to 85% RH (No condensation)1000 VAC for 1 minute between live parts and case50 M or more between live parts and case (at 500 VDC Mega)10 to 150 Hz at whichever is smaller of 1.5 mm amplitude or 20 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized)100 m/
24 V)Coil switching noise Note 5)Body portedLVM11Diaphragm type direct operated poppetN.C.2Air, Water, Pure water, Diluent, Cleaning solvent0 to 0.25 MPa1.5 mm10 ms or less (at pneumatic pressure)Zero leakage, either external or internal (at water pressure)0.38 MPa0 to 50C0 to 50C (with no condensation)11 lFreeIP40 or equivalent30 g12, 24 VDC?
EX500-GEN2_eng Description 1 Reserved (Fixed to OFF) 32.3 6 HOLD/CLEAR setting ON: Hold output at EtherNet/IPTM communication error. OFF: Set the output state at EtherNet/IPTM communication error via network. It is CLEAR, If none is set (at shipment). 28.3 Maintenance should be performed according to the Safety Instructions. Perform regular maintenance and inspections.
Please keep this manual handy for future reference. 6 7 (2) Mount and tighten the end plate and the valve manifold (intermediate reinforcing brace if necessary) at one end of the unit.
IN: M12 5-pin Plug, B-code Girakstrasse 8, AT-2100 Korneuburg, Austria Configuration Pin No.
(LED is OFF at normal condition) Power supply connector for output equipment IN-ERR Red LED is ON Indicates that an input power supply over current is detected. 1 (LED is OFF at normal condition) Connection example Indicates a communication error.
PSE57 -28 Current output: 4 to 20 mA Allowable load impedance: 500 or less (at 24 VDC) 100 or less (at 12 VDC) Caution After maintenance is complete, perform appropriate functional inspections and leak tests. Stop operation if the equipment does not function properly or there is a leakage of fluid. When leakage occurs from parts other than the piping, the product might be faulty.
Piping port Connected to the fluid inlet at IN side and to the fluid outlet at OUT side. Used as switch output device (ZS-33-D(M)) To obtain the operation manual about this product and control unit, please refer to the SMC website (URL https://www.smcworld.com) or contact SMC directly.
Connected to the fluid inlet at IN and to the fluid outlet at OUT. PFMB7102 0.5 to 0.7 Nm Safety Instructions Piping port D PFMB7102 E The body of the product. Body S S S These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or "Danger".
Piping port Connected to the fluid inlet at IN side and to the fluid outlet at OUT side. [F_2] Unit selection function 1 [ U_1] L/min Body The body of the product. [oU1_0] Instantaneous output mode Selection of output mode Display instantaneous flow Display accumulated flow / Connector Connector for electrical connections.
PF2A551 12 to 24 VDC Blue DC(-) 22 to 24 Nm Rc(NPT)3/8 PF2W504(T) Piping port Connected to the fluid inlet at IN side and to the fluid outlet at OUT side. 1 5 Rc(NPT)1/2 28 to 30 Nm PF2W520(T) 34 mm Bracket Bracket for mounting the product.
PF2W2 series Power and output socket Socket for the power and output connection. 1: In window comparator mode, the hysteresis is fixed at 3 digits. When setting, allow 7 digits or more between Set point 1 and Set point 2. 2: When Set point 1 = Set point 2, chattering may occur.
Piping port (Tube) Connected to the fluid inlet at IN side and to the fluid outlet at OUT side. These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or "Danger".