A large digital display provides a clear view of the current and set values.
A large digital display provides a clear view of the current and set values.
A large digital display provides a clear view of the current and set values.
A large digital display provides a clear view of the current and set values.
A large digital display provides a clear view of the current and set values.
SMC Pneumatic Clean Series When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
This chapter has been formulated to have a description of the Function Block, a diagram of the Function Block as seen on the LCD Display, and a logic table to show how the Output is controlled by the input signals. An Input that is ON (or High) is shown as a 1 while an input that is OFF (or Low) is shown by a 0.
Thermo-con. (1) Flow rate of recirculating fluid is a little.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
, 2(B) port] 24 13.3 13.3 24 16.2 16.2 34 17 36.7 34 B 2 PE B 2 B 2 B 2 B 2 B 2 B 2 B 2 B 2 B 2 R 3 R 3 P 1 1 P A 4 X A 4 A 4 A 4 A 4 4 A 4 A 4 A 4 A 4 A 2-One-touch fitting [1(P), 3(R) port] Applicable tube O.D.: 8 2-One-touch fitting (X, PE port) Applicable tube O.D.: 6 2n2-One-touch fitting [4(A), 2(B) port] Applicable tube O.D.: 4, 6 U side D side (L4) Applicable connector: 26 pin MIL
After blowing, make sure to hang the product on a hook, etc. Caution 1. Clean specification is not available with this product. When using in a clean room environment, confirm the required cleanliness before use. A minute amount of particles are generated due to wearing of the emitters while the product is operating. Wiring / Piping Warning 1.
I"P.1/4, .. . , ASP530F-N03-11 S 3/S' ~ 25.9 1 51Jtr 11 / 16" 28.6 ~6~5 ~ 61 ;a.: ~:B-.9 :2D.S 220 tU6' /36,3 . 34:7 .26~ 21.7 . . ~ A efertlllCe dll'l'lerlSlons 1 01 NPT Ihmads aller installalion 3 Speed Controller 5 . ASP w"" P;lo' Ch.,k V,'v. efles Construction Parts list .QesCr;plian ' ''' fi1t~lal , . . .
^-'-t" +'' l' tv."' 2',Sr " ,:; . a . ' li'J.Sh.' A--T.Tr/ir.{ 8r " 4 ' l e A . a ' A . , .
Then, a correct operation works until a vacuum pressure proportional to the input signal is reached, and a vacuum pressure is obtained which is always proportional to the input signal.
^-'-t" +'' l' tv."' 2',Sr " ,:; . a . ' li'J.Sh.' A--T.Tr/ir.{ 8r " 4 ' l e A . a ' A . , .
Please note that the graph should only be used as a guide, as there is a tolerance of about 10% in the clamp cylinder body.
In general, a mesh of about 50 to 100 is a guideline for the filter. When using ordinary tap water, scaling and sludge from substances in hard water such as calcium and magnesium can cause solenoid valves to malfunction. It is therefore necessary to install a water softener to remove such substances and a filter (strainer) immediately before the solenoid valve.
-1.8WDC WF333O Exhaust Conter NVF343O GNced Center (B) (A) (B) (a) 01 c2 \ t \ T I'f E I J E Z (R2)(PxFl) (R2XPXR1) Prssure Center NVF3530 (B) (A) Spej;ifications -, Flurd-Art f Operatangprssurcrange2Positionsingle2O-12gPSlS(1.5-9kgF) U 2 pooition double-1 5 1 28 PSI (1 9kgf/cm'?